663190
8
Zoom out
Zoom in
Previous page
1/15
Next page
EN
EN
Replacing Shifter Cables
Remove cable hardware from both
cables and remove shift cables
from housing.
Adjusting Cable Slack
Cable slack can be adjusted
with the barrel adjusters (1) at the
shifter.
Cable slack can be determined
by pulling lightly on the cable
housing (2) at the shifter and
noticing any slack.
f
0.5mm of slack is ideal. Cable
slack of more than 2.0mm may
cause decreased shift perfor-
mance and shift cable durability.
f For rear wheel removal, ad-
ditional cable slack may be
desired to ease shift cable
hardware removal, which can
be obtained with the barrel
adjusters.
4. BASIC MAINTENANCE AND CARE
Lubrication
fThe NuVinci N360 CVP is
provided with permanent
lubrication and the CVP
internals are maintenance-free
for the life of the product.
fThe NuVinci N360 internal
freewheel mechanism is
serviceable.
fRegular lubrication will extend
the chain’s service life.
13
14
Cleaning
fYour NuVinci N360
components are sealed and
well protected from the external
environment. However, do not
use water under pressure (such
as pressure washers or water
jets) for cleaning to prevent
malfunctions due to water
penetration.
fDuring the winter season, you
should clean your bicycle in
shorter intervals so that winter
road salt cannot cause any
damage.
fDo not use aggressive cleaners.
5. SERVICE INSTRUCTIONS
Remove the Phillips screw
(1) on the bottom of the NuVinci
shifter and remove the bottom
cover by pulling lightly on the
access tab (2).
Using a small at screwdriver
or pointed object, extract the
cable anchors (3) and shift cables
(4) from the grip pulley.
fRotate the grip to access
individual cable anchors.
Install one shift cable, allowing
the shifter housing (5) to guide the
cable around the internals until it
comes out the other side. Guide
the cable through the closest barrel
adjuster (6).
Pull the cable through the
barrel adjuster until the cable
anchor seats fully into the grip
pulley (7).
fRotate the grip to position the
next cable for installation and
repeat 5.3 and 5.4.
Reinstall the bottom cover and
screw (1). Torque to 0.2-0.3 Nm
(2-3 in-lbs).
4.1
4.2
5.1
5.2
5.3
5.4
2
1
4.1
4.2
1
2
3
4
5
6
7
5.1
5.2
5.3
5.4
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NuVinci N 360 - 2012 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NuVinci N 360 - 2012 in the language / languages: English as an attachment in your email.

The manual is 5,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NuVinci N 360 - 2012

NuVinci N 360 - 2012 User Manual - German - 15 pages

NuVinci N 360 - 2012 User Manual - Dutch - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info