803238

Nuk Eco Control Video Display 550VD - 10749102 Manual

13
Zoom out
Zoom in
Previous page
1/36
Next page
51
data (see "9. Technical data" on
page 74).
This automatically switches the baby unit
on.
Note: You can also wall mount the baby unit
in a suitable position with the enclosed
screws. Make sure you position the screws
45 mm apart for this.
4.3 Connecting baby unit and
parent unit
Normally, a connection is automatically
established between the two units when
they are switched on:
1. Make sure that the two units are always
within range.
2. To switch the baby unit 1 on, press the
On/Off button 10. To do this, press and
hold the On/Off button until the power
LED 8 lights up.
3. To switch the parent unit 17 on, press the
On/Off button 32 and keep it depressed
until the LED 21 lights up green.
You will hear a beep, the "Hello" screen
will appear, and the parent unit will begin
searching for the connection signal of the
baby unit.
While the connection is being set up, the
connection indicator 20 will light up red.The
screen will remain white and show no video
picture.
The corresponding blue symbol will
appear on the screen of the parent
unit.
As soon as the connection has been
established, the connection indicator 20
on the parent unit 17 and the VOX LED 7
on the baby unit 1 will light up green. The
connection symbol on the screen
disappears, and video transmission
starts.
If the connection setup is not successful
after 30 seconds the parent unit 17 will emit
a beep at regular intervals and the
connection indicator 20 will light up red.
The corresponding red symbol will
appear on the screen of the parent
unit to indicate that the connection
could not be set up.
4. First, check to be sure your baby is still
comfortable.
5. Then move the parent unit to a different
location within the range of the
connection signal so that a connection
can be set up successfully.
The parent unit and the baby unit will
automatically make repeated attempts to
connect until successful.
Note: If the connection indicator 20 begins
to flash green, this means that there is a
connection between the parent unit and the
baby unit, but your baby is currently asleep
and therefore the device has automatically
activated Eco-Mode to reduce the high-
frequency radio waves in baby’s room and
save energy.
Attention! While Eco-Mode is
active, video and sound
transmission is paused. The
screen will go white and the
corresponding symbol in the status bar will
show that Eco-Mode is active. The
connection between the two units remains
established, even while baby is sleeping.
4.4 Power supply
Baby unit
The power supply for the baby unit 1 works
only via the mains adapter. LED 8 lights up
green while the baby unit is on.
Parent unit
The parent unit 17 can be operated on
battery power with no mains connection for
up to 8 hours, or via the mains adapter, with
or without the battery inserted.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nuk Eco Control Video Display 550VD - 10749102 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nuk Eco Control Video Display 550VD - 10749102 in the language / languages: English as an attachment in your email.

The manual is 0.54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info