803238

Nuk Eco Control Video Display 550VD - 10749102 Manual

12
Zoom out
Zoom in
Previous page
1/36
Next page
50
4. Starting the device
Note: Always connect the cables before
inserting the mains adapter into the socket.
Always follow steps 1 to 5 in "4.1
Connecting the parent unit" in that order.
4.1 Connecting the parent
unit
The parent unit can be powered by the LiPo
battery included in the delivery or via the
mains adapter. The battery can be charged
with the aid of the mains adapter included in
the delivery.
Caution! To avoid a possible malfunction,
always insert the battery into the parent unit
before connecting the mains adapter.
1. Remove the battery cover 31 on the back
of the parent unit 17, by sliding it
downwards.
2. Insert the battery included in the delivery
package into the battery compartment.
The battery will fit only one way.
3. Slide the battery cover 31 back onto the
parent unit 17.
4. Insert the small plug of the mains adapter
into the mains adapter socket 29 of the
parent unit.
5. Insert the plug into a power socket that
matches the rating given in the technical
data (see "9. Technical data" on
page 74).
The parent unit will automatically switch
itself on and begin charging the battery.
The battery will be charged and LED 21
will start flashing.
Attention! Allow the battery to charge for
10 hours without interruption before
using the device for the first time, to
activate the full battery capacity. LED 21
flashes green during this time.
Subsequently, charging the battery will take
no more than about 6 hours, and you can
also charge the battery during operation.
Note: Battery power is permanently
shown in the status bar:
– Low battery power is shown
in the status bar.
– If battery power is very low,
the symbol starts flashing red. In
addition, LED 21 lights up red and a
warning appears on the screen
accompanied by a beep, to inform you
that the parent unit will switch off within
a very short time.
– LED 21 flashes green when the parent
unit is connected to mains power.
– If the parent unit is run in
mains power without the
battery being inserted, the
status line will show the symbol of a
power plug instead of the battery
symbol.
4.2 Connecting the baby unit
The baby unit automatically switches itself
on when it receives a fresh power signal
over the mains. This prevents the baby unit
from staying switched off when power is
restored after a short power failure.
Note: Don’t install the baby unit 1 until the
battery of the parent unit 17 is fully charged.
1. Put the baby unit 1 somewhere in the
nursery where your baby will not be able
to reach it.
An optimal distance between baby and
the baby unit is from 1 to 2 m.
Make sure the camera is set up to keep
your baby in the picture at all times, even
if the zoom function is active (see
"6.16 Zoom in / scroll image" on
page 72).
Note: Since the temperature sensor is
inside the baby unit it is important that
you do not cover it or place it near any
heat source. Direct sunlight may also
affect the reading.
2. Insert the mains adapter plug into the
socket 16 of the baby unit 1.
3. Insert the plug into a power socket that
matches the rating given in the technical
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nuk Eco Control Video Display 550VD - 10749102 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nuk Eco Control Video Display 550VD - 10749102 in the language / languages: English as an attachment in your email.

The manual is 0.54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info