Manual Novoferm Novomatic 403 (page 12 of 31) (English, Dutch, French, Spanish)

474197

Zoom out

Zoom in

1/31

Operating Instructions

Before carrying out any work to the

operator, always pull out the mains plug!

All persons using the door system must be

shown how to operate it properly and

safely:

When the operator is being used, the

opening and closing cycles must be

monitored.

Keep hand transmitters out of the reach of

children.

It must be ensured that neither persons

nor objects are located within the door's

range of travel.

Functional sequence

The garage door operator can be actuated via

impulse generators such as hand

transmitters, key switches etc. It is only

necessary to give a short, sharp impulse.

Initial impulse:

The operator starts up and causes the door to

travel to the set OPEN or CLOSE end-of-

travel positions.

Impulse generated whilst the door is moving:

the door stops

A new impulse:

the door continues to move but in the opposite

direction.

Internal safety device

If the closing door encounters an obstruction,

the operator stops and causes the door to

open to its top end-of-travel position in order to

clear the obstruction.

During the last 2 seconds of the closing cycle,

the door only opens slightly, this being

sufficient to clear the obstruction but

otherwise barring anyone from taking a look

into the garage.

If the opening door encountes an obstruction,

the operator stops immediately. The door can

be closed again by generating a new impulse.

External safety devices

Connecting plan figure 13

Wicket door contact (STOP A)

An open wicket door stops the operator

immediately or stops it from starting up.

Photocell (STOP B)

If the photocell is interrupted whilst the door is

closing, the door stops and reverses direction.

An interruption whilst the door is opening has

not effect.

Quick release

During adjustments, in the event of a power

failure or malfunctions the door can be

disengaged from the operator by actuating the

pull cord on the carriage and then operated

manually.

If the door is to be operated manually over a

longer period of time, then the existing locking

pin must be inserted (see figure 12). The door

latches, put out of service for power operation,

must be refitted, otherwise the door is not

latched in the closed position.

To restore power operation, return the locking

pin to the parking position (a) and put the

latches put out of service.

After an impulse has been generated, the door

automatically latches with the door operator.

Lighting

The lighting switches on automatically

whenever a start impulse is generated and

switches off again after the set time phase

(factory setting approx. 90 seconds).

A second button on the hand transmitter can

be programmed for 4-minutes light (figure 16).

When the button on the hand transmitter is

pressed, the light switches on independent of

the motor and switches off again after approx.

4 minutes.

Changing the light bulb:

Pull out the mains plug and open the lamp

cover using a Phillips screwdriver size 2 x 100.

Replace the light bulb (230 V, 40 W, base E27)

and screw the lamp cover back on.

Signal light

If a signal light for signalling the opening and

closing phases is installed, this flashes

together with the lamp in the operator as soon

as a start impulse is generated. The operator

starts with a time-delay in accordance with the

set warning phase (see menu stage 7).

Hand transmitter

Programming further hand transmitters:

See menu stages 1 and 2 (figure 15 and 16).

Changing the battery: Slide back the battery

compartment cover on the hand transmitter.

Take out the battery.

Insert a new battery (alkaline 23A, 12V) and

be sure polarity correctly!

Slide the cover back on.

Empty batteries must be disposed of

separately (toxic waste)!

Maintenance / Checks

For your own safety we recommend

that the door system be checked by a

specialist after initial installation and

then regularly at intervals of 1 year

minimum.

Monitoring the force limit

The operator control unit features a 2-

processor safety system to monitor the force

limit. The integral force cut-out is

automatically tested at each end-of-travel

position.

The door system must be checked before

being put into service and at least once a year

thereafter, during the course of which, a check

of the force limit facility (figure 21) must also

be carried out!

Caution! If the closing force is set too

high, persons can be placed at risk of

injury.

The opening force can be re-adjusted in menu

stage 5, the closing force in menu stage 6.

Dear customer,

During production the garage door operator

you have purchased has undergone various

checks by the manufacturer to ensure that it

is of impeccable quality. Should this operator

or parts of it prove to be of no use or limited

use as a result of proven material or

manufacturing defects, we shall rectify this,

at our discretion, through free-of-charge

repair or replacement.

We shall not accept any liability for damage

as a result of unsatisfactory fitting and

installation, improper putting into service,

incorrect operation and maintenance,

excessive use and overloading as well as

Terms of the Guarantee

We shall not bear the costs for dismantling

and installation, freight and carriage. If a

complaint is proven to be unjustified, the

customer must bear our costs.

This guarantee is only valid in conjunction

with the signed invoice and commences on

the day of delivery. The manufacturer

guarantees that the product is free of defects.

The warranty is granted for a period of 24

months, in as far as the verification overleaf

has been properly filled out. Otherwise the

warranty shall expire 27 months after the date

of manufacture.

Any alterations or modifications carried out to

the operator and accessory parts by the

customer. The same shall also apply for

damage incurred during transit or as a result of

force majeure, external influences or natural

wear as well as special atmospherical

stresses. We cannot accept any liability

following alterations or modifications of

functional parts carried out by the customer.

We must be notified of any defects

immediately in writing; on request the parts in

question are to be made available to us.

Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm Novomatic 403 in the language / languages: English, Dutch, French, Spanish as an attachment in your email.

The manual is 1,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Novoferm Novomatic 403

Novoferm Novomatic 403 User Manual - English, German, Dutch, French, Spanish - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Novoferm Novomatic 403 Manual

Product: