609307
14
Zoom out
Zoom in
Previous page
1/29
Next page
15
MULTICLEANER 7-53
Original Instructions
7.2 Installation
7.2.1 Frost in the
MULTICLEANER
Do not operate the robot if it has been exposed to frost without
having been frost protected. Then at first let it thaw. If parts of the
motor / motor pump unit are frozen, the safety valve will open and
the pump block will burst.
The robot must be placed so that the operator will always have ac-
cess to the display and the knobs during the automatic operation
without having to pass the robot, meaning that the display end of
the robot must turn to the access side during operation.
Lead the robot into the aisle ensuring that the distance between the
aisle and the right driving wheel is 5-10 cm.
7.2.2 Placing of the robot in
the aisle
7.2.3 Laying/connection of
water hose
The MULTICLEANER is fitted with a pivot joint/quick connector
placed under the front bumper for connection of a ¾" water hose for
the supply of water to the high pressure washer.
The water hose between the water tap and the MULTICLEANER
must have a minimum length of:
Minimum length of water hose = length of aisle + 3 metres
It is assumed that the water tap is placed at the end of the aisle.
Check that the water hose is not twisted before starting the opera-
tion as this may lead to stoppage.
Place the water hose parallel to the inventory side on the opposite
side of the sensors to avoid that the MULTICLEANER runs over the
water hose.
7.2.4 Fixing of cable in the
aisle
Connect the electric plug on the cable reel to the power take-off,
3x400V, 16A at the end of the aisle. The cable must be centred and
fixed with the cable relief in front of the cable reel to ensure an even
winding up / unwinding during operation. At the same time the ca-
ble between the cable relief and the power take-off will be relieved.
Check that the cable is tense before starting the machine.
Note ! The cable reel provides 35 m cable. Check that the travel
length of the MULTICLEANER is consistent to the length of the
cable on the drum. This is done by connecting the CEE plug to the
power take-off and centre and fix the cable to the floor in the driving
aisle in the front of the cable reel. Manually push the machine for-
wards until there are approximately two turns left on the cable reel
and then mount stop plate in front of the machine. Pull the machine
backwards to starting position. Now the washing can be started.
It is the responsibility of the user to make sure that there is an ob-
stacle to activate the front bumper at max. 35 metres.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk-ALTO MULTICLEANER 7-53 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk-ALTO MULTICLEANER 7-53 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info