641176

Niagara B264 Standalone Encoder Manual

24
Zoom out
Zoom in
Previous page
1/120
Next page
24
Hardware Version: This indicates the board version number. Balanced audio support is
available for version 4 and later. All other functionality is the same across hardware
versions.
Rear Module: This indicates the status of the Rear I/O Module. It can have one of the
following states:
o OK: The Rear Module is the correct module for the B264. In the B264 this
indicator will be always green.
o Not Installed: The B264 is not connected to a rear module. The card is
operating normally, but it will not be useful as there are no input and output
connections to it.
o Wrong Module: The B264 is connected to a rear module that was not
designed for it (most likely from another openGear® vendor). Depending on the
signals present on that module, there may be a small chance of damage to the
B264; Niagara Video recommends that this situation be rectified immediately.
This alarm will cause the front status LED to turn red. A card with hardware
version 3 or lower will show this alarm for the balanced audio rear I/O panel.
Analog Audio Input: This indicates the type of analog audio input (balanced or
unbalanced). This field will have an indication of unknown for
unrecognized/unsupported rear I/O panels.
Card Uptime: Indicates how long the card has been running since it was last rebooted.
Ambient Temperature: Temperature, in degrees centigrade, of the air intake of the card
(measured at the front edge of the card).
Internal Temperature: Temperature, in degrees centigrade, at the back of the card.
MDP Core Temperature: Temperature, in degrees centigrade, of the core MediaStorm
processing element.
The openGear® frame is designed to operate in environments with up to 40
o
C ambient. There is
typically a 5
o
C temperature raise from the external ambient to the “Ambient Temperature”
measured by the B264. If that measurement is at 45
o
C or higher, action must be taken to cool
down the ambient temperature.
The B264 modular versions are designed to operate in environments with an ambient
temperature between 0 and 50
o
C.
Network Tab
The Network Tab allows for configuration/monitoring of the two streaming Ethernet ports, and
optional configuration of DNS servers.
Network Configuration Tab
The Network Configuration Tab is further divided into the following tabs:
The Interfaces tab is used to set the individual parameters for each of the streaming
Ethernet ports.
The DNS tab is used to optionally configure DNS servers.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Niagara B264 Standalone Encoder at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Niagara B264 Standalone Encoder in the language / languages: English as an attachment in your email.

The manual is 3,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Niagara B264 Standalone Encoder

Niagara B264 Standalone Encoder Quick start guide - English - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info