629274

NetworX NX-595E IP Communication Module Manual

32
Zoom out
Zoom in
Previous page
1/36
Next page
32 © 2015 UTC Fire & Security Americas Corporation, Inc. All rights reserved.
ii. Segment 2: 168
iii. Segment 3: 1
iv. Segment 4: 1
5. Enter location 24 (DNS Server 2).
a. Follow the same steps as setup for DNS Server 1.
Configuring the NX-595E with the NetworX panel keypad -
Worksheets
Location 0: Reserved
Location 1:
Segment 1:
Option 1: Zone Doubling: When enabled, this feature will allow the two onboard zones to
double to four zones. Please refer to feature 18 for starting zone number. If this feature is
unselected, both onboard zones remain as single end of line zones and require 3.3K resistors.
When Zone doubling is enabled, Lower zones = 3.7K, Higher zones = 6.9K (not available on NX-
4 panels).
Options 2-8: Reserved
Segment 2-3: Reserved
Location 2-17: Reserved
Location 18: Zone Starting Number:
Location 18 is used to enter the starting zone number of the additional zones on the NX-595E. The
two zones can also be zone doubled, please refer to feature 1 to enable the zone doubling feature.
0 = Disabled.
Data
Zones
Data
Zones
Data
Zones
Data
Zones
9
=
9 - 12
41
=
41 - 44
73
=
73 - 76
105
=
105 -108
17
=
17 - 20
49
=
49 - 52
81
=
81 - 84
113
=
113 - 116
25
=
25 - 28
57
=
57 - 60
89
=
89 - 92
121
=
121 - 124
33
=
33 - 36
65
=
65 - 68
97
=
97 - 100
Location 19 - IP Feature Options
Location 19 is used to set required network settings.
Segment 1:
Option 1: Enable DHCP: When enabled, the NX-595E will automatically receive its IP address
from the network router. If this Option is disabled, the NX-595E will need to have its IP address
set manually. It is recommended that this Option be enabled.
Option 2: Reserved
Option 3: Enable Web Update: When enabled, allows updating of the NX-595E Configuration
Server's web pages via FTP. Normally disabled.
Option 4: Enable Ping: The “Ping” command is always functional while the NX-595E is in
program mode. Disable this option to allow the NX-595E to ignore "ping" commands in normal
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NetworX NX-595E IP Communication Module at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NetworX NX-595E IP Communication Module in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info