629274
30
Zoom out
Zoom in
Previous page
1/36
Next page
30 © 2015 UTC Fire & Security Americas Corporation, Inc. All rights reserved.
No Jumper (Dry Contact Switching)
Dry contact closure provided to output terminal. Maximum Load 30 VAC @ 1 A or
24 VDC @ 1 A. DO NOT exceed these ratings.
Jumper between GND and C (Negative Switching)
Bus Ground provided to output terminal @ typical 0V. Do not exceed relay rating
which is maximum load 30 VAC @ 1 A or 24 VDC @ 1 A.
Jumper between C and 12 V + (Positive Switching)
Bus Voltage provided to output terminal @ typical 12-13 VDC. Maximum Load @
12 V is total panel current; this includes all connected keypads and expansion
modules. Consult your panel’s specifications for maximum current rating. Do not
exceed relay current rating of 1A.
Caution: Do not exceed the Maximum Load ratings above for the relay
configuration. Exceeding the maximum rating could result in possible damage to the
product.
WARNING: DO NOT CONNECT MAINS VOLTAGE TO THE NX-595E. DOING SO
COULD DAMAGE THE MODULE OR NETWORX PANEL AND POSE AN
ELECTRICAL HAZARD THAT COULD RESULT IN A FIRE OR CAUSE SERIOUS
ELECTRICAL SHOCK OR LOSS OF LIFE.
Current Limit Caution: Check the current requirements of your load before
connecting! There is no overcurrent protection on the relays when providing bus
ground or bus voltage (jumper between GND and C, or C and 12 V +). You must
ensure your load does not exceed the recommended limits above. Exceeding limits
can damage the module. NetworX panels do have overcurrent protection on the
bus and may disconnect the bus to provide temporary protection. If enabled, your
panel will report "Overcurrent Fault" or "Expander Overcurrent". Repeated
overcurrent conditions can result in permanent damage to the panel or connected
devices.
Advanced Network Setup
If the IP address is empty (Location 21, Segment 1 will be 0 in the NetworX panel),
then you will have to manually program the network settings into the NX-595E. This
is an unlikely scenario as most routers are configured to automatically assign
network settings with DHCP. Before you manually configure the NX-595E, verify
with the network administrator or home owner that they have disabled DCHP in the
router. You will need the following settings from the network administrator or home
owner if they have DHCP disabled:
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NetworX NX-595E IP Communication Module at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NetworX NX-595E IP Communication Module in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info