629274
10
Zoom out
Zoom in
Previous page
1/36
Next page
10 © 2015 UTC Fire & Security Americas Corporation, Inc. All rights reserved.
Introduction
The NX-595E is an IP communication module that can be added to a NetworX V2
family security product (NX-4, NX-6, NX-8, NX-8E) to provide remote access and
alarm reporting via standard Internet connections (IP). The NX-595E can utilize two
connection methods to your central monitoring station. It can connect directly to an
Osborne Hoffman (OH) NetRec receiver. Alternatively, it can use UltraSync
services. Contact your central monitoring station to determine their preferred
connection method.
The security panel can be configured for alarm reporting exclusively over IP when
PSTN connectivity is no longer available. Alternatively, it can utilize the PSTN for
failover connectivity in the event the IP communications path is lost.
The NX-595E provides a web browser interface accessible via a local computer,
smart phone or tablet to configure the device. Additionally, UltraSync™, an Apple
®
iOS
®
or Android
®
application, is available for remote configuration and end user
control of the security system including control of two output relays. Up to four
zones are also supported with zone doubling (not available on NX-4 panels). Three
email addresses can be programmed into the NX-595E to allow alarm and trouble
events to be emailed to the end user.
This manual assumes the installer is familiar with the NetworX V2 family of security
products and is capable of programing the security system. It also assumes that the
installer is familiar with basic computer networking and Apple iOS or Android smart
devices.
Setup is a simple process:
1. Install the NX-595E into the NetworX panel.
2. Enroll the NX-595E into the NetworX panel.
3. Minimum configuration is required:
a. Time and daylight savings setup (Feature Menu)
b. IP Reporting (IP Reporting Menu)
c. Enable remote UltraSync application support by setting the Web Access
Passcode (Network Settings Menu)
Important notes before proceeding
The PINs for accessing the NX-595E are stored in the NetworX panel. Make
sure you are using the existing PIN for the Installer when configuring the NX-
595E.
Record the following information in the UltraSync Quick Reference Guide during
the installation process:
NX-595E serial number (12-digits)
Web Access Passcode (8- numerical digits)
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NetworX NX-595E IP Communication Module at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NetworX NX-595E IP Communication Module in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info