470014
24
Zoom out
Zoom in
Previous page
1/32
Next page
24
NAVMAN
FISH 4200 Installation and Operation Manual
Warning
1 Amp fuses must be positioned where shown in
the wiring diagrams.
If possible, route the transducer cables away from
other wiring on the boat. Electrical noise from engine
wiring, bilge pumps and other electrical equipment
can affect the unit.
The shortest and most direct connection to the boat's
battery helps to minimise voltage drop. Ensure that
any cable connections do not lay in the bilge.
Two wiring options are described in this section:
· Basic Wiring. This does not start the fishfinder
automatically when the boat ignition is switched
on and it disables the engine hours counter.
· Auto Power Wiring. This must be used for
engine hours and fuel computer options.
Important
The FISH 4200 must be run off a 12 volt battery and
must not be run off a circuit without a battery.
Basic Wiring
Black wire: Connect this to the negative battery
terminal.
5-4 Wiring Connection
1A fuse
1A fuse
1A Fuse
Red
Yellow
Black
Main
switch
12 V DC
Red wire: Connect this to the 12V positive battery
terminal after the main switch. Fit a 1 Amp fuse as
shown.
Yellow wire: Connect this to the black wire. This
disables the engine hours counter.
Power on the fishfinder manually whenever the main
switch is on.
White (NMEA
out)
Green
External
Beeper or
Light
Red
Yellow
Black
Main
switch
12 V DC
Ignition
switch
To ignition
system
Auto Power Wiring
Black wire: Connect this to the negative battery
terminal.
Red wire: Connect this to the 12V positive battery
terminal after the main switch. Fit a 1 Amp fuse as
shown.
Yellow wire: To enable the engine hours counter
and start the fishfinder automatically when the
ignition is turned on, connect the yellow wire to the
ignition system, through a 1 Amp fuse. Note that
the fishfinder cannot be turned off while the ignition
is on.
Flashing Light and/or External beeper
Use the green wire, if desired, to connect a
secondary alarm indicator such as a flashing light
or a 12V external beeper with a built in drive circuit.
Refer to the wiring diagram. If the external beeper
or light requires more than 250mA DC total, fit a
12V relay. Consult your NAVMAN dealer for more
advice.
NMEA Instruments
Use the white wire, if desired, to connect the
fishfinder to other NMEA instruments such as
NAVMAN’s depth repeater. See section 5-5 for more
information.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman FISH 4200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman FISH 4200 in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info