470014
23
Zoom out
Zoom in
Previous page
1/32
Next page
23FISH 4200 Installation and Operation Manual
NAVMAN
Correct installation is critical to the performance of
the FISH 4200. There are two components to install,
the display unit and the transducer. It is vital to read
5 Installation
the entire installation section of this manual and
the documentation that comes with the transducer
before attempting installation.
5-1 What comes with the FISH 4200?
Optional transducers
· Through hull Speed/Temperature transducer
· Through hull Depth transducer
· In hull Depth transducer
Other options and accessories
· Replacement paddle wheel
· Adapter cable for through hull transducer
· Carry bag
· Transducer extension cable
· Fuel kit (single or twin available)
Standard configuration
· FISH 4200 display unit
· Power cable
· Mounting bracket (screws included)
· Warranty registration card
· This manual
· Transducer (includes cable kit and screws)
· Transducer Installation Manual
· Screws
· Sun cover
· Flush mounting kit
5-2 Options and Accessories
There are two mounting arrangements:
· Flush mounting requires a solid panel
with access behind for wiring and mounting
screws.
· Bracket mounting requires a panel for
mounting the bracket. The bracket can be
rotated and tilted.
Select a position where the display head will be:
· at least 4" (100 mm) away from the compass.
· at least 12" (300 mm) away from any radio
transmitter.
· at least 4' (1.2 m) away from any antenna.
· easy to read by the helmsman and crew
while underway.
· protected from physical damage during
rough sea passages.
· easy to access the 12 volt power source.
· convenient to route the transducer cables.
Bracket mounting
1. Fix the mounting bracket onto the boat using the
three stainless steel screws. Do not overtighten
as the bracket may not rotate.
2. Push the display unit onto the mounting
5-3 Mounting the FISH 4200 Display Unit
bracket and tighten it firmly using the knob on
the mounting bracket.
3. Attach the cables
Removing the FISH 4200
The FISH 4200 can be removed after each use for
protection against the environment or security
reasons.
When removing the FISH 4200 ensure that the plugs
left in the boat are not exposed to the elements. Push
the attached dust covers over the exposed ends of
the plugs. Keep the display unit in a dry clean place
such as the optional NAVMAN carry bag.
Flush mounting
1. Cut a hole in the bulkhead for the display
unit using the flush mount template.
2. Drill four holes for the mounting studs
using the flush mount template.
3. Screw the four studs into the brass inserts
in the back of the display unit.
4. Sit the display unit in place and fit the
washers and nuts to the studs.
Depth Repeater
Repeater for Depth, Speed, Water Temperature,
Battery Voltage (see section 5-5).
Please consult your NAVMAN dealer for more
information.
Power cable
Mounting
bracket
Transducer
Unit
Screws
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman FISH 4200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman FISH 4200 in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info