512555
21
Zoom out
Zoom in
Previous page
1/77
Next page
21
FUEL 3100 / DIESEL 3200 Installation and Operation Manual
NAVMAN
6 Troubleshooting
This troubleshooting guide assumes that this
manual has been read and understood.
It is possible in many cases to solve difficulties
without having to send the unit back to the
manufacturer for repair. Please follow this
troubleshooting section before contacting the
nearest Navman dealer.
There are no user serviceable parts. Specialized
methods and testing equipment are required
to ensure that the unit is reassembled correctly
and is waterproof. Repairs to the unit must only
be carried out by a service centre approved by
Navman NZ Limited. Users who service the unit
themselves will void the warranty.
More information can be found on our website:
www.navman.com
1 Instrument will not turn on:
a Power/data cable is damaged or
disconnected. Perform a visual check.
b Fuse is blown or circuit breaker has tripped.
Replace the fuse or reset the circuit breaker.
c Battery voltage is outside the range 9 to
30 V DC. Check the battery voltage using a
multimeter.
2 The word SIM flashes at bottom left
corner of screen, values displayed are
unexpected:
a The instrument is in simulation mode (see
section 2-9).
3 Fuel reading is wrong or erratic:
a Check for leaks in the fuel line or in the fuel
pickup in the tank.
b Fuel sensor cable is unplugged or damaged.
Perform a visual check. DIESEL 3200: check
the LED light on the underneath of flow
sensor blinks when the engine draws fuel.
c The fuel REMAINING reading is incorrect.
The fuel tank capacity (SIZE) may be
incorrect, or the fuel REMAINING setting
may not have been updated after a refill.
See section 5.
d Sensors require calibration (see section 3-4;
diesel sensors do not normally need to be
calibrated).
e The fuel flow sensor may have been
mounted too close to the fuel pump, or
may be subject to excessive vibration. Refer
to the installation instructions supplied
with the fuel sensor.
f The fuel flow sensor damping (dAmP.F)
value is not suitable for the engine. Check
that the value is not set to zero and then try
increasing the value until a steady flow rate
is shown (see section 3-5)
4 Speed reading is wrong or erratic:
a Speed readings require the optional speed
sensor to be installed and setup (see
section 3-6).
3 If the boat has twin tanks, press ENT. Then
press until the display shows the name of
the tank to be filled, PORT or STBD.
4 Write down the number displayed, FUEL,
which is the amount of fuel now in the tank.
5 Add fuel to the tank, writing down how
much you add.
6 Add together the two figures you have
written down, to calculate the amount of
fuel now in the tank. Press ENT. Then press
or hold to change FUEL to the amount
of fuel now in the tank.
7 Press ENT, then press ESC to return to the
main display.
8 If the boat has twin tanks and you are
adding fuel to the other tank as well, repeat
the above steps.
Note:
If you follow procedure b above every time you
add fuel, then a small error will accumulate,
because it is hard to measure exactly how
much fuel you add. To avoid this, about every
ten tankfulls of fuel, fill the tank and follow
procedure a.
c When you remove fuel from a tank
Repeat the steps for procedure b above, but:
i This time subtract the fuel you have
removed from the original amount of fuel
in the tank to calculate the amount of fuel
now in the tank.
ii Press or hold to change FUEL to the
amount of fuel now in the tank.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman Diesel 3200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman Diesel 3200 in the language / languages: English as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman Diesel 3200

Navman Diesel 3200 User Manual - German, Dutch, French - 77 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info