512555

Navman Diesel 3200 Manual

20
Zoom out
Zoom in
Previous page
1/77
Next page
20
FUEL 3100 / DIESEL 3200 Installation and Operation Manual
NAVMAN
To check out the installation:
1 Power on the boat and any other
instruments. Check the instruments work
properly.
2 Enter the setup data (see section 3).
Set dUAL, motor , and InPUt first, then
enter the rest of the setup data.
For boats with twin tanks or twin engines,
remember to enter port and starboard data
separately where required.
3 Fill the fuel tank(s) and set the fuel in the
tank(s) in the FUEL 3100 or DIESEL 3200 (see
section 5).
4 On boats with twin engines, check the
installation of the port and starboard fuel
sensors:
• DIESEL 3200: Start the port engine. Check
the LED lights under the sensors are
blinking. This indicates the sensors are
operating correctly. Confirm the fuel flow is
being displayed as port engine fuel usage
on the instrument. (If it is being displayed
as starboard engine fuel usage, swap
over the fuel flow sensor connectors on
the ‘T’ connector.) Repeat the check with
starboard engine.
• FUEL 3100: Start the port engine. Confirm
the fuel flow is being displayed as port
engine fuel usage on the instrument. If it is
being displayed as starboard engine fuel
usage, reconfigure the settings (see section
3-3).
5 FUEL 3100 only: Calibrate the fuel sensor(s)
(see section 3-4).
6 If a paddlewheel speed sensor is
connected, calibrate it (see sections 3-8
and 3-9).
7 Take the boat for a trial run and check the
unit is displaying the correct data.
FUEL 3100: Recalibrate the FUEL 3100’s fuel
sensor(s) after the first 100 engine hours (see
section 3-4).
When you add or remove fuel from a tank, you
must enter into the FUEL 3100 or DIESEL 3200
how much fuel you have added or removed.
Otherwise REMAINING, RANGE and the low
fuel alarm will be meaningless. Twin tanks
connected by an open balance pipe should be
trated as a single fuel tank.
When you add or remove fuel from a tank:
a When you fill a tank
1 Fill the tank.
2 Press until REMAINING is displayed.
3 If the boat has twin tanks, press ENT until
the display shows the name of the tank you
have filled, PORT or STBD.
4 Press and together.
5 If the boat has twin tanks and you are filling
the other tank as well, repeat the above
steps.
Note:
It is often very difficult to refill underfloor
fuel tanks to the same level twice, due to air
pockets. Because of this, owners of boats with
underfloor fuel tanks should:
• Ensure the boat is trimmed to sit at
the same angle in the water each time
procedure a above is followed.
• Mostly use procedure b below when filling
the tank, but use procedure a above about
every tenth fill.
b When you fill or part fill a tank
1 Before adding or removing fuel, press ESC
and ENT together, then press until the
FUEL setup menu is displayed.
2 Press ENT, then press or until the
FUEL data is displayed.
5 When you add or remove fuel
4-7 Testing the installation
4-8 Resetting to factory defaults
To reset to factory defaults:
1 Turn the power off.
2 Hold ENT + while turning on the power
and for at least five seconds after.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman Diesel 3200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman Diesel 3200 in the language / languages: English as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman Diesel 3200

Navman Diesel 3200 User Manual - German, Dutch, French - 77 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info