512550
8
Zoom out
Zoom in
Previous page
1/12
Next page
8
DEPTH 2100 Installation and Operation Manual
NAVMAN
5 Installation
Instrument Installation
The instrument can be easily installed in different
types of instrument panels.
1. Select a suitable location for the instrument.
When selecting the location for mounting, the
following are recommended:
• Controls of the instrument must be
accessible to the user.
• Electrical connections must be routed to
the boat system as directly as possible,
minimising the length of cable where
practical.
• Location should provide as much protection
from the elements as possible.
• The panel for mounting the instrument
should be 3 mm to 19 mm (1/8 to 3/4 inch)
thick.
• The space behind the instrument panel
must have a depth of at least 95 mm (3.75
inches).
2. Drill a 51 mm (2-inch hole) on the instrument
panel in the selected location.
3. With the mounting bracket removed, insert the
instrument into the hole until the back of the face
plate is flush with the outside mounting wall.
4. Slide the bracket over the body of the
instrument. Note: Orient the bracket in such a
manner that it does not cover the buzzer.
5. Tighten the mounting nut until the bracket is
secure.
6. Connect the power cord at the back of the
instrument to a 12 V power supply which is
active whenever the ignition switch is on.
The red lead should be connected to the
positive terminal of the power supply via
a 1 amp fuse or a 1 amp circuit breaker.
• Red (+) Terminal
• Black (-) Terminal
• Orange External Buzzer
Use for optional external buzzer (use red (+)
terminal to complete circuit). If unused then
tape to avoid shorting.
• Brown Data input/output
Your Depth 2100 can be used as a repeater for
another DPT or DBT NEMA depth sounder. If
unused then tape to avoid shorting.
IMPORTANT: If unsure about wiring contact
your nearest NAVMAN dealer.
Bracket
Buzzer
RCA Jack
Connector
600 mm (24 inch)
Power Cord
Black (-)
Red (+)
Orange
Brown
6 Wiring
The black lead should be connected to the
negative terminal.
7. Obtain the power from a 12 V source as
directly as possible. Avoid power circuits which
share loads with ignition, alternators, radio
transmitters, etc. Excessive electrical noise
associated with such devices may prevent the
instrument from operating properly.
8. Connect the RCA phono plug on the
transducer cable to the instrument. Extension
cables are available from your NAVMAN dealer
if the transducer cable is too short.
Instrument Panel
Mounting
Bracket
51 mm (2 inch) Hole
Instrument
Sealing Gasket
2.5"
63.5 mm
.75"
19.0 mm
3.75"
95 mm
Mounting Nut
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman Depth 2100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman Depth 2100 in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman Depth 2100

Navman Depth 2100 User Manual - German - 10 pages

Navman Depth 2100 User Manual - Dutch - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info