493513
8
Zoom out
Zoom in
Previous page
1/15
Next page
1 FM ANTENNA TERMINAL: Connect the supplied wire dipole” FM
antenna to the FM antenna terminal using the supplied balun adapter.
It will usually work best when mounted on a vertical surface such as a
wall, with arms fully outstretched forming a horizontal T perpendicular
to the origin point of the signal.
2 AM ANTENNA TERMINAL: Connect the supplied AM loop antenna to
these terminals. If an external AM antenna is used, make connections
to the AM and GND terminals in accordance with the instructions
supplied with the antenna. Refer also to the item about ASSEMBLING
THE LOOP ANTENNA at the LISTENING TO AM/FM RADIO section of the
OPERATION page.
3 OUTPUT (L, R): Connect to the corresponding analog audio input of
an amplier, receiver or stereo system.
4 RS-232: Connect this interface using RS-232 serial cable (not supplied)
to any Windows® compatible PC to allow remote control of the C 426
via compatible external controllers. NAD is a certied partner of AMX
and Crestron and fully supports these external devices. Check out the
NAD website for information about AMX and Crestron compatibility
with NAD. See your NAD audio specialist for more information.
5 IR IN: This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another component to allow
control of the C 426 from a remote location. Most NAD products with IR
OUT are fully compatible with the C 426.
6 +12V TRIGGER IN: This input allows the C 426 to be switched remotely
to standby mode and ON by ancillary equipment, such as an amplier,
preamp, AV processor, etc. The controlling device must be equipped
with a 12V trigger output to use this feature. Connect this +12V trigger
input to the remote component’s corresponding +12V DC output jack
using a mono cable with 3.5mm male plug.
7 AC MAINS INPUT: The C 426 comes supplied with a separate AC Mains
cable. Before connecting the cable to a live wall socket, ensure that it
is rmly connected to the C 426’s AC Mains input socket rst. Connect
only to the prescribed AC outlet, i.e., 120V 60 Hz (for 120V version
models of C 426 only) or 230V 50 Hz (for 230V version models of C 426
only). Always disconnect the AC Mains cable plug from the live wall
socket rst, before disconnecting the cable from the C 426’s Mains input
socket.
If you intend not to use the C 426 for long periods of time, disconnect
the AC mains cable plug from the live AC wall socket.
WARNING
If the male plug of the mono cable (with or without +12V DC) is
connected to C 426’s +12V TRIGGER IN, the Standby button in the front
panel as well as the corresponding ON/OFF function keys in the remote
control will be disabled. Unplug the mono cable to maintain normal
power ON/OFF function procedures.
IDENTIFICATION OF CONTROLS
REAR PANEL
1 432 5 6 7
ATTENTION!
Please make sure that the C 426 is powered o or unplugged before making any connections. It is also advisable to power down or unplug all associated
components while making or breaking any signal or AC power connections.
8
ENGLISH FRAAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD C 426 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD C 426 in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD C 426

NAD C 426 User Manual - German - 14 pages

NAD C 426 User Manual - Dutch - 14 pages

NAD C 426 User Manual - French - 14 pages

NAD C 426 User Manual - Italian - 14 pages

NAD C 426 User Manual - Swedish - 14 pages

NAD C 426 User Manual - Spanish - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info