493513
10
Zoom out
Zoom in
Previous page
1/15
Next page
The C 426 oers very high quality sound from radio broadcasts. The
reception and sound quality will always be dependent to a degree however
on the type of antenna(s) used as well as proximity to the broadcast origin,
geography and weather conditions.
ABOUT ANTENNAS
The supplied ribbon-wire FM antenna can be connected to the rear panel
FM-antenna input using the included “balun” adapter and should be fully
extended to form a T. This folded-dipole antenna will usually work best
when oriented vertically, with the arms of its T fully outstretched and
arranged perpendicular to the origin of the desired broadcast. There are
no “rules however, and experimenting freely with antenna placement and
orientation may yield the clearest sound and lowest background noise.
In areas of poor FM reception, an exterior FM antenna can improve
performance dramatically. If radio listening is important to you, consider
consulting an antenna installation professional to optimize your system.
The supplied AM loop antenna will usually provide adequate reception.
However, an exterior AM antenna can be used to improve reception.
Consult an antenna professional for more information.
ASSEMBLING THE LOOP ANTENNA
1 Rotate the outer frame of the antenna.
2 Insert the bottom edge of the outer frame into the groove on the stand.
3 Extend the antenna cord.
SELECTING A TUNER BAND
Toggle front panel’s [FM/AM] button to select either AM or FM band. Using
the TNR 1, select desired band by directly pressing [AM] or [FM] button.
TUNING STATIONS
Toggle front panel’s [PRESET/TUNE] button to switch between “Preset” and
Tune” mode. Select TUNE mode (“TUNE” scrolls through the VFD) or PRESET
mode (“PRESET scrolls through the VFD).
1 Rotate the PRESET/TUNE control in either direction for more than 1
second to engage automatic tuning. The tuner will stop at the next
suciently strong signal it encounters. Note that this function “wraps”
– that is, it will continue to search from one end of the AM or FM band
to the other until it stops at a strong signal. Rotate the PRESET/TUNE
control again for more than 1 second to start searching again.
2 By briey rotating the PRESET/TUNE control in either direction, manual
tuning is engaged for precise tuning to a specic frequency. With each
brief rotation, the tuner will take 0.05 MHz steps at FM band and 10
kHz (120V version) or 9 kHz (230V version) at AM band. When tuned
accurately to a station, TUNED will be illuminated in the VFD. The
antenna bars displayed below the ANTENNA icon in the VFD reects the
signal strength of the tuned station.
Automatic tuning is available on both AM and FM band.
DIRECT TUNING
If you know your desired station’s frequency allocation, you can tune
directly to the station.
1 Toggle front panel’s [PRESET/TUNE] button to switch between “Preset”
and Tune mode. Select TUNE mode (“TUNE” scrolls through the VFD).
2 Using the numeric keys of the remote control, key-in the frequency
allocation of the station. For example, to enter 104.50MHz, press “1”, “0”,
“4”, “5” and “0” or press “1”, “0”, “4” and “5”.
STORING PRESETS
The C 426 can store a mix of your 40 favorite AM and FM stations for
immediate recall.
1 To store a Preset, tune rst to the desired frequency and then press the
front panel [MEMORY] button.
2 “MEMORY” and the next available Preset number will continually ash
on the VFD (If all 40 preset numbers are allocated already, you can
overwrite an existing Preset number. Rotate the PRESET/TUNE control
knob to select the Preset number you want to overwrite).
3 Press the [MEMORY] button again to store the desired frequency on the
Preset number shown (“STORED” scrolls through the VFD). Your desired
frequency is now stored in the assigned preset.
DIRECT RECALL OF A PRESET
You can directly recall a desired Preset number.
1 Toggle front panel’s [PRESET/TUNE] button to switch between “Preset”
and Tune mode. Select PRESET mode (“PRESET scrolls through the
VFD).
2 Using the numeric keys of the remote control, key-in directly your
desired Preset number.
DELETE A PRESET
1 Select the Preset number to be deleted.
2 Press and hold both the front panel [MEMORY] and [DISPLAY] buttons
until “DELETE” is shown ashing in the VFD. Immediately release both
buttons and then press [DISPLAY] button again (“DELETED” scrolls
through the VFD). Current Preset number is now deleted.
ABOUT USER NAMES
A particular Preset number can be assigned an eight-character “User Name”.
This applies only to stored AM stations and non-RDS FM stations. The
assigned “User Name” will be shown in the VFD whenever the associated
Preset number is recalled.
ENTERING USER NAMES
To assign a Preset number with the user name “NEWS”, follow the procedure
as below.
1 Recall the desired Preset number.
2 Press and hold [DISPLAY] button until the display shows a ashing
cursor point.
3 Rotate the [PRESET/TUNE] control knob to select the rst character of
the name (“N” from the alphabetical list).
4 Press [DISPLAY] button to select the character and correspondingly
move forward to the next position. Repeat this process for each
character in sequence.
5 Press the [MEMORY] button to store the User Name (“STORED” scrolls
through the VFD). The current Preset number is now assigned the user
name “NEWS”.
OPERATION
LISTENING TO AM/FM RADIO
10
ENGLISH FRAAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD C 426 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD C 426 in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD C 426

NAD C 426 User Manual - German - 14 pages

NAD C 426 User Manual - Dutch - 14 pages

NAD C 426 User Manual - French - 14 pages

NAD C 426 User Manual - Italian - 14 pages

NAD C 426 User Manual - Swedish - 14 pages

NAD C 426 User Manual - Spanish - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info