30282
15
Zoom out
Zoom in
Previous page
1/58
Next page
Instructions
Seite 15
ENGLISH
8.6. Recycling
Unlike NiCd cells, NiMH cells contain no cadmium,
which is a toxic heavy metal. Nevertheless, exhausted
cells should not just be thrown in the domestic rubbish.
Take the cells to your local specialist recycling centre.
The cells must first be discharged completely and made
safe against short-circuit (wrap in plastic film).
9. Using the transmitter for the
first time
9.1. Initial power-ON
When the transmitter is switched ON for the very first
time the following screen appears:
Use the up and down arrow keys to select the desired
language and confirm by pressing ENTER. This selection
can be changed at any time (Î 13.5.2.). All user-
definable text (e.g. names for mixers, models, assign-
ment lists) will not be changed, if the language selec-
tion is changed afterwards in the SETUP menu.
9.2. Switching on
When the you switch the transmitter ON, the following
power-on info screen will always appear briefly, regard-
less of whether an RF module is installed or not. This
gives information on the transmitter type, the current
software version and the languages available for the
screen texts:
If no RF module is fitted, the following message appears
briefly:Note: No RF!
9.2.1. Switching ON with the
HFM-4 RF module for crystals
After the power-on info screen (Î 9.1.), the last used
status display appears (Î Fehler! Verweisquelle
konnte nicht gefunden werden..). If everything is in
order, the software immediately activates the RF mod-
ule for crystals, and an RF (Radio Frequency) signal is
immediately transmitted. The LED starts to flash, the
screen switches to the last active status display, and the
transmitter is ready to use.
9.2.2. Switching ON with the
HFM-S synthesizer RF module
After the power-on info screen (Î 9.1.), the currently
set channel and transmission frequency appears briefly
for your information:
After this the last used status display appears. If every-
thing is in order, the software activates the synthesizer
RF module, and an RF (Radio Frequency) signal is im-
mediately transmitted. The LED starts to flash, the
screen switches to the last active status display, and the
transmitter is ready to use.
The first time you switch the transmitter ON with a syn-
thesizer RF module fitted, or after installing a different
synthesizer RF module, an information screen appears,
replacing the power-on info screen. This tells you how
to set the channel when using a synthesizer RF module:
The method of selecting a channel when using an HFM-
S synthesizer RF module is described in Section 9.4.
9.2.3. Switching on without transmitting an RF sig-
nal
Whether you are using an HFM-4 RF module for crystals
or an HFM-S synthesizer RF module it is possible to
switch the transmitter ON without transmitting an RF
signal, even when an RF module is installed. The trans-
mitter can then be operated in that mode. This can be
useful for programming when no RF signal is required,
e.g. to minimise current drain, or when your channel is
already in use.
Hold the tool button L pressed in when you switch the
transmitter on you are now at the power-on menu.
RF is OFF ( LED glows constantly)
The following display appears:
With HFM-4 RF module
for crystals
With HFM-S4
synthesizer RF module
Pressing any direct menu access button, or the ENTER
button, takes you to the last active status display.
!
Note:
RF stays OFF until the transmitter is switched ON again.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex ROYALevo9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex ROYALevo9 in the language / languages: English as an attachment in your email.

The manual is 3,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex ROYALevo9

Multiplex ROYALevo9 User Manual - German - 58 pages

Multiplex ROYALevo9 User Manual - Dutch - 110 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info