30282

Multiplex ROYALevo9 Manual

17
Zoom out
Zoom in
Previous page
1/58
Next page
Instructions
Seite 17
ENGLISH
The system monitors the current drain of the RF module
to check whether an RF signal is being transmitted or
not, rather than by checking the status of the RF mod-
ule. If the current drain is below a typical value, either
no RF signal is being transmitted, or the RF signal is
being transmitted at less than full power (in which case
safe operation cannot be guaranteed!) This method of
monitoring is much safer, as it is also capable of detect-
ing faults and errors::
x Is an RF module installed?
x Is the connection between RF module and trans-
mitter in order (contact fault)?
x Is the RF module working correctly?
x Is a crystal fitted, and is it in order?
(only with HFM-4 RF module for crystals)?
x Is the transmitter aerial installed, and is it making
proper contact?
If the ROYALevo is in use as a Pupil transmitter, or in
diagnosis mode, no RF signal will be transmitted => LED
glows constantly.
9.6. The status displays
There are four different status displays available in total.
You can switch between the individual status displays at
any time (provided that you are at one of the other
status displays, i.e. not in a menu) using the „V“ or „W“
buttons, depending on the information you wish to see.
When you switch the transmitter on, the last used status
display will always appear.
Status display
1
1
2
3
4
5
6
Bars
Line 1 Status of the 3-D digi-adjustors.
Numerous set-up parameters can be assigned
to the 3-D digi-adjustors, which can then be
varied directly (Î 10.2.2.)
Line 2 Current model memory with
No. of the memory (1): model name(BASIC)
Line 3 Current operating voltage of the transmitter
battery in numeric form, and also graphically
in horizontal bar form
Line 4
Version: ROYALevo 9 or ROYALevo 12
Line 5
User name (Î 13.5.3.)
Line 6 Operating time of the
current model memory(Î 17.1.)
Bars The 4 bars at the sides and bottom of the
screen show the current trim positions of the
4 primary control functions/sticks (Î 11.4.).)
Status display
2
(flight phases)
1
2
3
4
5
Line 1 Status of the 3-D digi-adjustors, see above
Line 2 Current model memory, see above
Line 3 Current operating voltage, see above
Line 4 Code letter of the switch used to change
flight modes (Î 18.4)
Line 5 Current flight mode with
No. (1): name (NORMAL)
Bars Current trim positions, see above
Status display
3
(Timers)
Only timers with assigned switches are displayed. Be-
hind the time the switch code letter is shown (P in the
example).
1
2
3
4
Line 1 Status of the 3-D digi-adjustors, see above
Line 2
Slot-Timer (Î 17.2.)
Line 3
Sum Timer (Î 17.3.)
Line 4
Interval Timer (Î17.4.)
Bars Current trim positions, see above
Status display
4
(system)
1
2
3
4
5
6
Line 1 Variant (ROYALevo 9 or 12),
software-version (e.g. 1.09),
language set currently loaded DE/GB
(Î 13.5.2.)
Line 2 with synthesizer module: channel no. freq.
else type of RF module (HFM-4) or "No RF"
Line 3 Transmission system (e.g. FM-PPM 9)
depending on servo assignment (Î 16.2.)
Line 4
available battery charge (Î 8.1.2 and 8.1.3.)
Line 5 residual operating time with the residual
charge at the current power consumption
(Î 8.1.2 and 8.1.3.)
Line 6 Overall operating time of the transmitter
(Î 17.)
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex ROYALevo9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex ROYALevo9 in the language / languages: English as an attachment in your email.

The manual is 3,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex ROYALevo9

Multiplex ROYALevo9 User Manual - German - 58 pages

Multiplex ROYALevo9 User Manual - Dutch - 110 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info