30242

Multiplex PROFIcar4000 Manual

8
Zoom out
Zoom in
Previous page
1/16
Next page
PROFI mc 4000PROFI mc 4000
Version 2.0
8
Slow for mixer input
;SERVO 5:ELEV.+
INPUT 2:ELEVATOR Ä
,02.0sec' #01.0sec_
The maximum delay time is 25 seconds, and the
value can be set separately for both directions.. The
time statement always refers to full servo travel, -
100% to +100% (=200%). For example, if you have
set 20% elevator trim compensation for the SPOILER
mixer input, then the elevator moves to the new set-
ting in 2.5 seconds.
Example:
Compensating for an unwanted pitching moment due
to incorrect motor downthrust (model climbs when the
throttle is opened).
The mixer ELEVATOR+ has been set up with
THROTTLE as one of the inputs. This provides a
means of correcting the model’s unwanted tendency
to climb when the throttle is opened. Nothing new
there.
What is new is that the „slow“ mixer can now be
added. Naturally the model’s unwanted pitching mo-
ment builds up gradually, i.e. it follows the model’s
rate of acceleration. Even if you use a switch to open
the throttle (electric motor), it can take several sec-
onds before the pitching moment takes full effect.
The same applies when you close the throttle (or
switch off the electric motor), but this time in reverse.
In the next section you will see how to adjust the
times for „running up“ (,0.00 sec') and „running
down“ (#0.00 sec_) for the input.
To correct the power moment we wish to add and
subtract the THROTTLE input slowly relative to the
ELEVATOR+ mixer. At the same time the application
of up- or down-elevator is slowed due to the set
SLOW delay, and this allows you to adjust the re-
sponse speed of the THROTTLE input to
ELEVATOR+ exactly to match the model’s behaviour.
This is how it’s done:
Button Effect
b b
Hot keys to reach
the „Servo adjustments“ menu
w
On to the „SLOW“ menu
Slow for mixer input
;SERVO 5:ELEV.+
INPUT :THROTTLE Ä
,02.0sec' #03.5sec_
-100% to +100% +100% to -100%
b
Open „Servo“ select field
and select the servo
(x) Open the „Input“ adjust field and select
the input to be adjusted
The input line only appears if more
than one input is present!
g or w Select adjust field for the desired di-
rection,
set time using q/n or the Digi-
adjustor, range 0,1 sec to 25,0 sec
6.2 Transmitter control options vary-
ing with flight mode
This is how it used to work:
If you moved to „Menu 1: Adjustments“ and select the
CONTROLS point, the top line of the screen always
displayed the name of the current flight mode.
This is how it works now:
The name of the flight mode is only displayed if the
selected option can be set differently in the various
flight modes.
If the setting applies to all flight modes (SLOW, trim
travel, trim method, AUTO-TRIM) then the top line is
left blank. This gives you a visual reminder that the
settings apply to all modes.
6.3 Control switch status
displayed on the screen
This is how it used to work:
When adjusting the switching threshold you could
previously only see the % value on the screen. You
could only check where the switching point lay with
reference to the transmitter control travel if the control
switch was also assigned to a function.
This is how it works now:
In „Menu 2: Assigning SWITCHES“ an asterisk („*“)
appears next to the control’s code letter if the associ-
ated control is in the „ON“ range.
Assign switches
CONTROL SW.: C1 Ä
;FROM CONTROL: A *
,1-POINT: MAX + 0%_
The same applies if you define the switch as a 2-
position switch.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex PROFIcar4000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex PROFIcar4000 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info