Manual MTD Zero Turn Serie Frontcut (page 13 of 18) (English)

495078

Zoom out

Zoom in

1/18

English Operating Instructions

Preparing for operation

 Park the appliance on a firm level

surface and lock the parking brake.

 Conduct all work with the engine

switched off.

 Remove the ignition key.

For all work on moving parts:

 Open the bonnet and disconnect

the cable to the spark plug.

Set the driver seat

Fig. 11

 Take your place on the driver seat.

 Adjust the seat to the desired

position.

Setting the steering wheel

Fig. 1

 Press and keep pressed the lever

(F).

 Adjusting the steering wheel.

 Release the lever, and make sure

that the steering wheel engages

correctly.

Setting the cutting mechanism

wheels (according to the

model)

Fig. 14

The cutting mechanism wheels

should be in the respective cutting

mechanism setting, always between

6–12 mm above the ground.

The cutter wheels are not designed

to bear the loads generated by the

cutters and may have to be offset

accordingly.

Setting the rear rollers

(if fitted)

Depending on the model, the rear

rollers can be attached in two

positions.

Fig. 15

“High” position (upper hole):

– Standard position – the grass is

not rolled or only minimally.

“Low” position (lower hole):

– Roll position – the grass is also

rolled after cutting.

 Remove safety split pin (1) from

the left side.

 Pull out axle (2) to the right.

 Insert axle into the required hole

(High/Low). When inserting the

rollers (3) and the spacer (4),

push back onto the axle.

 Align axle (2) with the groove and

push through the left holder.

Re-insert safety split pin (1).

Note

Always fit rear roller on both sides

in the same position (High/Low).

Starting the engine

 Take your place on the driver seat.

 Depress the brake pedal fully or

engage the parking brake.

 Switch off the engage switch

(PTO).

 Raise the cutters to the top.

 Set the throttle lever into

position .

 To cold-start the engine, pull the

choke or move the accelerator

lever to .

 Turn the ignition key to until the

engine is running (attempt to start

the engine for max. 5 seconds,

wait 10 seconds before attempting

to start the engine again).

When the engine is running, set

the ignition key to /I/ .

 Slowly push back the choke.

 Return the accelerator lever until

the engine runs smoothly.

Stopping the engine

 Move the throttle to the middle

position.

 Let the engine run for approx.

20 seconds.

 Set the ignition key to /0.

 Remove the ignition key.

 Engage the locking brake before

leaving the appliance.

Driving the appliance

t~êåáåÖ

^Äêìéí=í~âÉçÑÑI=ëíçééáåÖ=ëìÇÇÉåäóI=

~åÇ=ÇêáîáåÖ=~í=ÉñÅÉëëáîÉ=ëéÉÉÇë=ê~áëÉ=

íÜÉ=êáëâ=çÑ=~ÅÅáÇÉåíë=~åÇ=Å~å=Å~ìëÉ=

Ç~ã~ÖÉ=íç=íÜÉ=ìåáíK

kÉîÉê=ëÉíL~Çàìëí=ÇêáîÉêÛë=ëÉ~í=çê=

ëíÉÉêáåÖ=ïÜÉÉä=ïÜáäÉ=ÇêáîáåÖK

Note

Be especially cautious when

reversing. Never change direction

without first stopping the appliance.

Note concerning steering

The steering affects not only the

angle of the rear wheels, but also the

drive of the front wheels depending

on the angle of the steering wheel.

You can also turn this unit without

a turning radius (“zero turn” around

its own axis), i.e. when the unit is

turned, the front wheels act as

apivot.

– A small steering wheel angle up

to approx. 10° affects the rear

wheels only, i.e. you move a

normal turning radius.

– A larger steering impact beyond

10° additionally serves to make

the turning radius smaller up to

a “zero-turn”. As the steering

wheel angle increases, the drive

(speed) of the front wheels is

affected, i.e. the inner wheel

rotates slower and the outer

wheel quicker.

– Complete steering impact

additionally serves to make

a “zero-turn” (turning on own axle)

possible. The rear wheels are

adjusted as far as possible and

the drive (direction of rotation and

speed) of the front wheels is

affected simultaneously, i.e. the

inner wheel rotates backwards

and the outer wheel forwards at

corresponding speed reduction.

Note

The larger the steering impact is,

the greater the amount of power is

needed to turn. The driving speed is

reduced with increasing steering

impact. As soon as the steering

wheel is in the central setting again

(driving straight on) the tractor will

once again drive again at the speed

previously set.

Please pay attention to the fact that,

according to the model, tight turning

radii or “zero-turns” can lead,

if applicable, to damage to the

topsoil.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of MTD Zero Turn Serie Frontcut in the language / languages: English as an attachment in your email.

The manual is 2,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD Zero Turn Serie Frontcut

MTD Zero Turn Serie Frontcut User Manual - German - 18 pages

MTD Zero Turn Serie Frontcut User Manual - Dutch - 18 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

MTD Zero Turn Serie Frontcut Manual

Product: