Manual MTD Zero Turn Serie Frontcut (page 11 of 18) (English)

495078

Zoom out

Zoom in

1/18

English Operating Instructions

PTO-switch (I)

Fig. 8

The PTO switch switches the cutter

deck/accessories on and off via an

electromechanical clutch.

ON = pull the switch.

OFF = press the switch.

Note

When the safety lock system has

automatically switched OFF the

appliance (e. g. when reversing with

activated cutters), first switch ON and

then OFF the PTO switch to release

the lock on the clutch.

Combination indicator (J)

Fig. 9

According to the model,

the combination indicator can

consist of the following elements.

Oil pressure (1):

If the indicator light lights up when

the engine is running, switch the

engine off immediately and check

the oil level. Where necessary,

visit a garage.

Brake (2):

Indicator lamp lights up if the brake

pedal is not depressed or the

parking brake is not locked when

the engine starts.

Cutter deck (PTO) (3):

The indicator lamp lights up when

the cutters are not switched OFF

at engine start (PTO).

Battery charge indicator (4):

If the indicator light lights up when

the engine is running, this means

that the battery is not sufficiently

charged. Where necessary,

visit a garage.

Operating hour counter/

Battery voltage (5):

This function shows the operating

hours as full hours and

of an hour

in the display.

Note

– When the ignition is switched on,

the battery voltage indicator is

indicated for a short period and

then the operating hours are

indicated.

– The operating hours are always

counted except for when the

ignition key is in the “Stop”

position or when it is removed.

– Each time 50 operating hours

have elapsed (according to the

model), the oil change indicator

“CHG/OIL” appears in the display

for five minutes. This message

appears after the next two hours

of operation. See the engine

manual for oil change intervals.

Can holder (K)

Fig. 1

Gear release lock lever (L)

Fig. 10

To push the unit when the engine

is switched off, pull up both levers,

then pull out and press down.

To drive, put back/push in both

levers.

Engine hood holder (M)

Fig. 1

To open the engine hood,

remove the retaining rubber.

Seat adjustment lever (N)

Fig. 11

The driver’s seat can be set with

the seat adjustment lever.

Lever for setting the cutting

height (O)

Fig. 12

Largest cutting height, cutters top =

lever to “H”.

Smallest cutting height, cutters

bottom = lever to “L”.

To adjust the lever, press the button

(a) and adjust the lever (b). Release

button and engage lever in the

required position.

Note

When exchanging the cutting

height, the cutting mechanism

wheels/rollers have to be

correspondingly reset. See section

“Setting the cutting mechanism”.

Ratchet plate for setting the

cutting height (P)

Fig. 1

Cutting height can be adjusted from

approx. 3.8 cm to approx. 11 cm.

Each notch corresponds to a height

adjustment of approx. 0.9 cm.

Chokelevel (Q) (depending

on model)

Fig. 13

To start a cold engine, pull the choke

(Figure 13a), or move the accelerator

lever to (Figure 13b).

Arm rests (R)

Fig. 1

Hydraulic oil expansion tank

(S)

Fig. 1

Is used as an expansion vessel for

the hydraulic fluid during operation.

Maintenance and inspection only by

a specialist company during annual

maintenance.

Fuel tank (T)

Fig. 1

Tank contents display (U)

Fig. 23

shows the fill-level of the fuel tank

on the see-through window.

Light (optional)

The headlights are lit as long as the

engine is running or the ignition is

switched on.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of MTD Zero Turn Serie Frontcut in the language / languages: English as an attachment in your email.

The manual is 2,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD Zero Turn Serie Frontcut

MTD Zero Turn Serie Frontcut User Manual - German - 18 pages

MTD Zero Turn Serie Frontcut User Manual - Dutch - 18 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

MTD Zero Turn Serie Frontcut Manual

Product: