495078

MTD Zero Turn Serie Frontcut Manual

14
Zoom out
Zoom in
Previous page
1/18
Next page
Operating Instructions English
11
Start the engine as stated.
Release the parking brake.
Slowly engage the drive pedal until
you have reached the speed you
want.
Stopping the appliance
Release the accelerator.
Press the brake pedal until
the appliance is stationary.
Mowing
Never change the direction of
motion when the appliance is driving
or coasting (see “Driving the
appliance”)
Information on mowing
– In normal mowing mode
/I/ (see Operation,
ignition lock):
Before reversing the machine,
switch off and raise the cutter
deck.
– In reverse mowing mode
/I/ (see Operation,
ignition lock):
Exercise extreme caution when
reverse mowing and do not
activate unless absolutely
necessary.
Start the engine as stated.
Set the throttle lever into position .
Switch on the cutter deck (PTO).
Lower the cutters.
Release the parking brake.
The required speed is selected
with the forward drive pedal
(by slowly depressing it).
The appliance starts moving.
General information
When adjusting the cutting height
and driving speed, ensure that the
machine is not overloaded.
Depending on the length, type,
and dampness of the grass it may
become necessary to adjust the
cutting height and appliance speed
for the optimum grass catcher
performance.
If blockages occur, reduce the
driving speed and increase the
cutting height.
The best way to mow
Cut the first two rounds so the cut
grass is thrown out sideways into
the middle.
Never allow the grass to grow
too long
Never cut the grass too low.
Drive in a straight line.
Never mow at high speed,
particularly when a mulching kit
or grass catcher is installed.
Mulching
Various appliances can also mulch
when fitted with the corresponding
accessories. Ask your specialised
dealer for details.
Switching off the machine
Stopping the appliance:
Release the accelerator press
brake pedal until the appliance
is stationary.
Switch off the cutter deck.
Set the throttle lever into the middle
position.
Raise the cutters to the top.
Set the ignition key to “ /0”
after twenty seconds.
Engage the locking brake
before leaving the appliance.
Remove the ignition key.
Pushing the appliance
Fig. 10
Push the appliance only when
the engine is switched OFF.
The levers for releasing the gears are
situated on the left and right sides of
the frame behind the front wheels.
Unlocking the gear drive:
To push the unit when the engine
is switched off, pull up both levers,
then pull out and press down.
Release the parking brake.
Return the gear lock lever before
restarting the engine.
Note
Never tow the unit while the front
wheels are in contact with the
ground. This can cause serious
damage to the gears.
Tips on lawn care
Mowing
Lawns consist of various grass
types. Frequent mowing promotes
the growth of grass, resulting in
strong roots and a firm sward. If you
seldom cut the grass, you will
enhance the development of high-
growing types of grass and other
weeds, such as clover, daisies …).
The normal height of a lawn is
approx. 4–5 cm. Only
1
/
3
of the
overall height of the grass should be
mown; i.e. at 7–8 cm, cut at normal
height.
Try not to cut the grass shorter than
4 cm, otherwise the lawn will suffer
during dry periods. If the grass has
grown particularly high (forexample,
during a holiday period), cut it back
to its normal height in several
stages.
Mulching with accessory
(optional)
Fig. 16
The grass is chopped up fine
(approx. 1 cm) during mowing and is
left on the lawn. The lawn therefore
retains a lot of nutrients. Please note
the following:
Do not mow wet grass.
Never mow more than max. 2 cm
of the total grass length.
Drive slowly.
Have the engine at max. rpm.
Clean the mower cover regularly.
Note
Attach mulching accessory
depending on the model.
For installation examples see
Fig. 16a/b.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MTD Zero Turn Serie Frontcut at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MTD Zero Turn Serie Frontcut in the language / languages: English as an attachment in your email.

The manual is 2,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD Zero Turn Serie Frontcut

MTD Zero Turn Serie Frontcut User Manual - German - 18 pages

MTD Zero Turn Serie Frontcut User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info