549869
17
Zoom out
Zoom in
Previous page
1/69
Next page
EN-17
Basic operation (continued)
When fine streaks are seen on projected
images
This is due to interference with the screen surface and
is not a malfunction. Replace the screen or displace
the focus a little.
Power-off
Use the following procedure to turn off the projector.
The lamp may deteriorate if the projector is powered
off and on repeatedly within 30 minutes after the lamp
is lighted.
1. Press the POWER button on the control panel or
the STANDBY button on the remote control.
• Themessage“PowerOff?Press again”
appears on the screen.
• Tocancel,pressanybuttonexceptthePOWER
button.
(Some buttons on the remote control don’t
function for cancel.)
2. Press the POWER button on the control panel or
the STANDBY button on the remote control within
10 seconds again.
• ThelampwillgooutandtheSTATUSindicator
will start blinking.
3. Wait about 90 seconds for the STATUS indicator to
be turned off.
4. Unplug the power cord.
• ThePOWERindicatorwillgoout.
• Ifthepowercordshouldbeunplugged
accidentally while either the STATUS indicator is
blinking or the lamp is on, allow the projector to
cool down for 10 minutes with the power off. To
light the lamp again, press the POWER button
(or ON button). If the lamp doesn’t light up
immediately, repeat pressing the POWER button
(or ON button) two or three times. If it should still
fail to light up, replace the lamp.
Important:
• Thetipoftheprojectionlensoftheprojector
protrudes. Therefore, be sure to put the lens cap on
the lens for protection when carrying the projector.
• Whenstoringtheprojectorinthecarryingcase,the
lens should face up.
Direct Power OFF
You can turn off this projector just by unplugging the
power cord without pressing the POWER button.
• Don’tshutdowntheprojectorwhiletheSTATUS
indicator is blinking after the lamp lights up
because the lamp’s life may be shortened.
• Don’tturntheprojectorbackonrightaftershutting
it down because the lamp’s life may be shortened.
(Wait about 10 minutes before turning the projector
back on.)
• Beforeshuttingdowntheprojector,besuretoclose
the menu screen. If you shut down the projector
without closing the menu, the setting data of the
menu may not be saved.
• Ifyoushutdowntheprojectorwhilecontrolling
the projector using the network function, the
application software such as ProjectorView may
fail. For details, see “User Manual of LAN Control
Utility” contained in the CD-ROM.
AUTO POSITION button
When the image isn’t projected in the right position
with Computer selected as the input source, follow the
procedure below.
1. Project a bright image such as the “Recycle Bin”
window on the full screen.
2. If the screen saver is running, turn it off.
3. Press the AUTO POSITION button.
• Iftheimageisstillnotintherightposition,
adjust the image position using the Signal menu.
See page 24.
Volume from the speaker
Press the VOLUME or button to change the
volume from the speaker.
The volume control bar will appear on the screen.
16
Volume
• Thevolumecontrolbarwilldisappearabout10
seconds after the VOLUME button is released.
• TheVOLUMEbuttonsdon’tfunctionwhilethe
menu is being displayed.
• Whenahigh-levelaudiosignal,suchasaDVD
audio signal, is supplied to the AUDIO IN terminal,
the output from the speaker may be distorted.
You can change the volume also by using the Volume
setting in the Audio menu.
(See page 21 for menu setting.)
1. Display the Audio menu.
2. Select Volume by pressing the or button.
3. Adjust the volume by pressing the or button.
4. Press the MENU button to exit the menu.
AV mute
The video and audio signals are temporarily muted
when the AV MUTE button is pressed. To cancel
muting, press the AV MUTE button again.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD390U-EST at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD390U-EST in the language / languages: English as an attachment in your email.

The manual is 10,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Mitsubishi WD390U-EST

Mitsubishi WD390U-EST Additional guide - English - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info