■For allowable temperature setting ranges, refer to the range setting of set temp.
■Reference set temp
Cooling … 26 to 28°C Dry … 24 to 26°C Heating … 20 to 24°C Fan … Setting temp is not required.
■If the Auto is selected for the set temp, the set temp display shows “0”. Temperature can be adjusted higher or lower with using ▲▼ buttons. Note that Auto is not displayed and
cannot be set when SC-SL2, SC-SL3, or SC-SL4 is connected.
■If the Back button is tapped without tapping the Set button, the selected set temp is invalidated and the display returns to the TOP screen.
Change flap direction
Menu
Direction
Cooling
16：14
(Mon)
F1: High power
Timer
Now stopping.
Set temp
F2: Energy-saving
Change flap direction
Ind. flap
Control
Back
4
Tap the desired ap direction. After
selecting the ap direction, the display
returns to the Select ap screen. (☞
1)
5
When the 3D auto ow operation is
enabled, “3D AUTO” is displayed on
the Change flap direction button, as
shown on the left.
Menu
Direction
Auto
16：14
(Mon)
F1: High power
Timer
Now stopping.
Set temp
MEETING1
Room
3D AUTO
F2: Energy-saving
Select flap
Upper/lower flap
Back
Select the flap to change.
Left/right flap
3D AUTO2
1
R/CRoom
Outdoor
3
■When multiple IUs are connected to the remote control for a mixed environment consisting of FDKs with a left/right flap and IUs without a left/right flap, enabling the 3D auto flow operation will set the
models without a left/right flap to a flap position set before the 3D auto flow operation was started.
■Since the flap is controlled automatically in the following operation, it may differ from the display on the R/C.
∙ When the room temperature is higher than the set temp (In case of the heating operation)
∙ When the “In operation for heating standby. ” or “In operation for defrosting.” is displayed (In case of the heating operation).
Cool air is blown horizontally not to blow directly to human body.
∙ In a high humidity environment (during cooling operation)
■When you select Auto swing while the Anti draft setting is enabled, the flap will not swing and be set at flap position 1.
■Changing the left/right flap direction and 3D auto flow operation cannot be performed from the SC-SL2, SC-SL3, or SC-SL4. Also note that 3D auto flow operation will not be disabled when you
change the flap direction from the SC-SL2, SC-SL3, or SC-SL4 during a 3D auto flow operation.
1 Tap the Change flap direction button on the TOP screen.
When an FDK with a left/right ap is not connected: ☞2
When one or more FDKs with a left/right ap are connected: ☞3
Change flap direction
Ind. flap
Control
Auto swing
Back
OutdoorRoomR/C
Select the flap direction.
2
When the Change ap direction screen is displayed, tap the button of desired ap direction.
To swing the ap, tap the Auto swing button.
To x the ap position, tap one of 1 to 4 buttons.
After selecting the ap direction,
When an FDK with a left/ right ap is not connected, the display returns to the TOP screen. (☞1)
When an FDK with a left/right ap is connected, the display returns to the Select ap screen. (☞3)
3
When one or more FDKs with a left/right ap are connected, the Select ap screen is displayed. Select the desired ap direction.
①
To change the up/down ap direction, tap the
Upper/lower flap
button. The Change ap direction screen for the up/down
ap is displayed. (☞2)
②
To change the left/right ap direction, tap the
Left/right flap
button. The Change ap direction screen for the left/right ap is
displayed. (☞4)
③
The 3D auto ow operation automatically controls the fan speed and ap direction to efciently condition the air of the entire
room.
To switch to the 3D auto ow operation, tap 3D AUTO to enable the operation.
To disable the 3D auto ow operation, tap the 3D AUTO again. The ap direction returns to the direction that was set before
the 3D auto ow operation was enabled. The 3D auto ow operation will also be disabled when you change the up/down or left/
right ap direction during the 3D auto ow operation.
Note
・ Do not manually move the flaps or panel with anti draft by force. It could damage these flaps and panels.
・ Do not blow air downward for a long period of time during the cooling operation. Condensation may be generated and water may drip from the side panel. (In case of Ceiling suspended type)
・ For FDKs with a left/right flap, it is recommended that the flap should be set toward the right side when there is a wall on the left, or set toward the left side when there is a wall on the right. For more
information, refer to the Notes in the Individual flap control section.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Mitsubishi RC-EX3 - REMOTE CONTROL at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Mitsubishi RC-EX3 - REMOTE CONTROL in the language / languages: English as an attachment in your email.
The manual is 6.18 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
Others manual(s) of Mitsubishi RC-EX3 - REMOTE CONTROL
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
