■Operation modes which cannot be selected depending on
combinations of IU and OU are not displayed.
■When the Auto is selected, the cooling and heating switching
operation is performed automatically according to indoor
and outdoor temperatures.
CoolingFan
DryHeating
Auto
Change operation mode
Fan
Heating
Back
Auto
Dry
OutdoorRoomR/C
Cooling
Please select operation mode.
Change set temp
Menu
Direction
Cooling
16：14
(Mon)
F1: High power
Timer
Now stopping.
Set temp
F2: Energy-saving
Menu
Direction
Cooling
16：14
(Mon)
F1: High power
Timer
Now stopping.
Set temp
F2: Energy-saving
Change set temp
Auto
Set
Back
OutdoorRoomR/C
Tap
▲▼
to set temp & tap [Set].
Push the Run/Stop switch.
Operation lamp (green) lights and operation starts.When the operation stops, all operation buttons on the screen turn
off. When the set lighting time of backlight is counted up, the
backlight turns off.
When the screen is tapped, the backlight lights, and all operation
buttons are displayed.
Note
・ Do not shut down the power supply immediately after the stop of operation.
It should be waited for more than 5 minutes till the residual operation time of drain
motor is counted up. Otherwise, it could cause water leakage or breakdown.
Press the Run/Stop switch while the unit is in operation.
The operation lamp turns off and the operation stops.
・ A message “Invalid request” may be displayed when a button is pushed. This is not a fault but it is because the button operation is set to the “Disable”.
・ The unit starts to operate initially with the following settings after the power on. These settings can be changed as desired.
Central control …… OFF
Operation mode …… With auto mode: Auto cooling
…… Without auto mode: Cooling
Set temp …… 23.0°C
Fan speed …… 3-speed
Flap direction …… When cooling: position 2, when heating: position 3
＊When an FDK with a left/right flap is connected, left/right flap direction: center, 3D AUTO: disabled
・ In the following cases, a message “Operation mode is invalid.” is displayed and it changes to the fan operation, because operation modes are not matched.
① When Heating (including auto heating) is selected for Operation mode while using an OU for cooling only.
② When Heating is selected for Operation mode while controlling multiple units including units allowed for both cooling and heating and units for cooling only.
③When different operation modes are selected between IUs which are connected to a OU that do not allow mixed operation of cooling and heating.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Mitsubishi RC-EX3 - REMOTE CONTROL at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Mitsubishi RC-EX3 - REMOTE CONTROL in the language / languages: English as an attachment in your email.
The manual is 6.18 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
Others manual(s) of Mitsubishi RC-EX3 - REMOTE CONTROL
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
