31038
48
Zoom out
Zoom in
Previous page
1/80
Next page
46
On LCD Programming
On LCD Programming is a programming method to set the timer recording on the
remote control LCD and transfer it to the VCR. For example, setting the timer
recording of the program on channel 2, on the 12th from 10:00 am to 11:00 am, in
SP mode:
1 Load a tape with its erasure prevention tab intact into the VCR.
2 Press LCD PROGRAM on the remote control. The display for programming
the timer recording will appear on the remote control LCD and CH will flash.
3 Turn the ADJUST dial to choose the channel you would like to record. Turn the
SHUTTLE ring to the right.
If you are using a cable box that the VCR cannot control, enter the channel
number on which the cable box sends a signal to your VCR (usually channel
3 or 4).
If you are recording from a DSS
®
, PRIMESTAR
®
or DISH Network
satellite
receiver, simply choose the channel you would like to record; for example,
channel 245. S will display next to the channel number.
To record from an external source, press INPUT or turn the ADJUST dial to:
Select L1 for a source connected to the rear panel.
Select L2 for a source connected to the front panel.
4 DAY will flash. Turn the ADJUST dial to choose the day on which you want to
record.
Your choices are:
a single day up to one month away.
every day from Monday through Friday; for example, to tape a soap opera.
To program, turn the ADJUST dial until DAILY appears.
the same day every week; for example, to tape your favorite weekly sitcom.
To program, turn the ADJUST dial until E- (for EACH) and the desired day of
the week appears.
Turn the SHUTTLE ring to the right once you have made your choice.
5 The hour numbers of the start time will flash. Turn the ADJUST dial to set the
hour when recording is to start. Turn the SHUTTLE ring to the right.
6 The minute numbers of the start time will flash. Turn the ADJUST dial to set
the minutes when recording is to start. Turn the SHUTTLE ring to the right.
7 Set the stop time the same way as the start time, using steps 5 and 6.
8 Press SP/EP under the flip cover of the remote control to select the recording
mode.
select SP if you want to record in SP mode.
select EP if you want to record in EP mode.
do not make a selection if you want to keep the recording in the mode that
was previously used.
9 Press TRANSFER. The programmed contents will be transferred to the VCR,
and Recap screen will appear. The program you have chosen to record will be
highlighted.
Make sure that the programming contents shown on the screen is correct.
IMPORTANT
If you cannot select the other program line by turning ADJUST dial on the
remote, press PAUSE first, and then turn the ADJUST dial.
Timer Recording
VCR-A
DAYCH
ON OFF
VCR-A
DAYCH
ON OFF
VCR-A
DAYCH
ON OFF
am
VCR-A
DAYCH
ON OFF
am
pm
TRANSFER
SP
VCR-A
DAYCH
ON OFF
¬Program to record
CH DAY ON OFF
10 TH15 9:00p10:30pSP
§ 2 MO12 11:30a 1:30pSP
--- -- --:-- --:-- SP
--- -- --:-- --:-- SP
ππππππππππππππππππππππππ
Use ADJUST to select,
and ENTER.
Press MENU to go back.
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi HSHD2000U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi HSHD2000U in the language / languages: English as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info