31038
49
Zoom out
Zoom in
Previous page
1/80
Next page
47
IMPORTANT
You cannot transfer the program while the VCR is recording or on recording
pause mode.
If you have already programmed 8 recording events, Program memory is full
will appear on your screen for 8 seconds, and then the Recap screen will
appear. Use CANCEL to erase an entry before you can add another one.
If two programmed recording times overlap, VCR is already programmed for
that time will display on your screen for about 8 seconds, and then the Recap
screen will appear. The program you have just set will flash for 3 seconds
and the start time and the stop time will be shown in red letters. The start
and stop time of the overlapped program will be highlighted in red color. You
will need to erase one of them.
If you set the impossible date, The date is wrong. Please re-enter the date.
will be displayed on the screen for 8 seconds.
If the remote control is failed to transfer, The transfer is failed. Please
transfer again will be displayed on the screen for 8 seconds. To transfer the
same programming contents again, press TRANSFER twice. Pressing
TRANSFER once displays the programming contents on the remote control
LCD again, and pressing it again transfers the displayed program.
10 To program additional recording times, follow the procedure from step 2 to 9
again.
11 When you are finished with all programming, check the following:
If you have a cable box, a digital cable box, a PRIMESTAR
®
or a DISH
Network
satellite receiver, leave the cable box or receiver turned ON.
If your VCR does not control your cable box, leave the box tuned to the
station you wish to record.
Turn the VCR power OFF and make sure the programmed recording light is lit.
IMPORTANT
To cancel programming while programming with the remote control LCD,
press LCD PROGRAM.
To cancel programming while displaying the Recap screen, press CANCEL
to cancel the selected program, and then press MENU to exit the Program to
record menu.
Timer Recording Hints
To use the VCR before timer recording begins, press POWER on the remote once.
This turns the programmed recording light off and the VCR on.
If you use POWER on the front panel for this purpose, press it twice. Pressing it
once turns off the programmed recording light; pressing it again turns the VCR on.
When you are finished using the VCR, turn the VCR power off again. Make sure
the programmed recording light is back on.
After a program has been recorded, the VCR memory of that program is cleared
(unless you have scheduled the VCR to record the program every day or every
week).
If there is already a program in the VCR’s memory, you will see the Recap screen
when you bring up the menus for programming to record (unless you are program-
ming with the QUICK PROGRAM). If the VCR’s memory is full, Program memory
is full will appear on the screen. If so, you must erase a program before you can
enter a new one.
Timer Recording
VCR POWER
REC
REC
POWER
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi HSHD2000U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi HSHD2000U in the language / languages: English as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info