517341

Metz MECABLITZ 50 AF-1 digital Pentax Manual

99
Zoom out
Zoom in
Previous page
1/182
Next page
99
ķ
9.2 Cordless flash mode
9.2.1 Remote slave flash mode ( )
The flash unit supports Pentax is wireless P-TTL Remote System in slave flash
mode. At the same time, one or more slave flash units can be remotely control-
led from one master or controller flash unit on the camera (e.g. mecablitz 58
AF-1P digital).
So that multiple remote systems in the same room do not interfere with one
another, there are four independent remote channels available (CH 1, 2, 3 or
4). Master, controller and slave flash units belonging to the same remote system
must be set to the same remote channel. The slave flash units must be able to
receive the light from the master or controller flash unit with the integrated sen-
sors for the remote mode ቦ.
Depending on the camera model, the camera’s internal flash unit can
also function as master or controller flash unit. Please consult the respec-
tive camera operating instructions for further tips on setting the master
or controller flash unit.
Setting procedure for remote slave flash mode
• Press the button combination „Select“ until
„ “ flashes in the display.
• Apply the setting desired with the buttons
+ and —.
– When „On“ is displayed,
the remote slave mode is activated.
– When „OFF“ is displayed,
the remote slave mode is deactivated.
The setting takes effect immediately.
After about 5 seconds the display stops flashing and the setting is saved auto-
matically. After activation of the remote slave mode, „ “ appears in the
display. In addition, the remote channel is shown (CH).
SL
SL
☞
SL
Setting of the remote channel
The same remote channel must be set on the slave flash unit as on the
master or controller flash unit!
• With the remote slave mode activated,
press the button combination „Select“ until
„CH“ (= remote channel) flashes in the display.
• Apply the setting desired with the buttons + and —.
Selection of group 1, 2, 3 or 4 is possible.
The setting takes effect immediately.
After about 5 seconds the display stops flashing and the setting is saved auto-
matically. After activation of the remote slave mode, „ “ appears in the
display. In addition, the remote channel is shown (CH).
Use flash unit mounting foot S60 (optional accessories, see 17) to set up the
slave flash unit. When the slave flash unit is flash-ready, the AF measuring flash
also flashes ቭ.
SL
☞
On
SL
SL
☛
☛
CH
2
☛
☛
CH
2
709 47 0191.A3 50AF-1 Pen. 17.12.2010 13:22 Uhr Seite 99
… 99 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metz MECABLITZ 50 AF-1 digital Pentax at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metz MECABLITZ 50 AF-1 digital Pentax in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info