517338
86
Zoom out
Zoom in
Previous page
1/174
Next page
86
ķ
4 LED displays on the flash unit
4.1 Flash readiness indication
When the flash capacitor is charged, the flash readi-
ness symbol lights up on the flash unit, indica-
ting that the flash is ready to fire. This means that flash
light can be used for the next shot. Flash readiness is
also transmitted to the camera and indicated accor-
dingly in the camera’s viewfinder (see 6).
If a shot is taken before the flash readiness indicator appears in the camera’s
viewfinder, then the flash unit will not be triggered and, if the camera has alrea-
dy switched to flash sync speed (see 11.1), the shot may have the wrong expo-
sure.
4.2 Correct exposure indication
The correct exposure indication „OK“ only lights up
for about 5 seconds if the shot was correctly exposed
in TTL flash mode ( , E , E HSS; see 7)!
If no „OK“ exposure indication appears after the shot,
then the shot was underexposed. You will need to
repeat the shot with the next smaller f-number (for
example, f/8 instead of f/11) or the distance to the
subject or reflecting surface (for example, with bounce flash) will have to be
reduced. Note the maximum flash range indicated on the display of the flash
unit (see 5.2).
TTLTTLTTL
5 Information in Display
The Canon cameras transmit the settings for ISO, lens focal length (mm) and
aperture to the flash unit. It calculates the maximum flash range from the set-
tings and their guide number. Flash mode, range, aperture and zoom position
of the main reflector are displayed in the display of the flash unit.
If the flash unit is operated without having received data from the camera, only
the flash mode selected, the zoom position of the main reflector and „Zoom“ is
displayed. The displays for aperture and range only occur once the flash unit
has received the data required from the camera.
Zoom, aperture and flash range are only displayed on cameras where
the aperture and ISO values are transmitted to the flash unit!
Display illumination
Every time a button on the flash unit is pressed, the flash display illumination is
activated for 10 seconds. When a flash is fired via the camera or the hand
release on the flash unit, the display illumination is switched off.
5.1 Display of the flash mode
The current flash mode is shown in the
display. Depending on the type of camera,
different displays are available for the selected TTL
flash mode (e.g., , E , E HSS) and the
manual flash mode M (see 7).
5.2 Range display
The flash range is displayed when using cameras that transmit ISO, lens focal
length and aperture data. For this a data exchange must have occurred bet-
ween the camera and flash unit, for example by tapping the shutter release.
The range can be displayed either in metres (m) or feet (ft) - see 9.7.
The flash range is not displayed when no data is transmitted from the
camera.
TTLTTLTTL
F 5,6
7,5
m
Zoom
105
mm
TTLE
TTLE
709 47 0175.A2 50 AF-1 C 26.08.2010 15:52 Uhr Seite 86
86


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metz MECABLITZ 50 AF-1 digital Canon at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metz MECABLITZ 50 AF-1 digital Canon in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info