Manual Metabo TP 7500 SI (page 11 of 56) (English, German, Dutch, Danish, French, Finnish)

600858

Zoom out

Zoom in

1/56

ENGLISH

 Unplug the pump and allow

to cool. A specialist must

check the system to make

sure it is in perfect working

order before it can be used

again.

Danger! Risk of electric

shock!

 Do not touch the plug with

wet hands! To unplug

always pull at the plug, not

the power cable.

 Connect only to an earthed

outlet that is properly

installed, earthed and

tested. Mains voltage and

fuse protection must corre

spond to those stated in the

"Technical Specications".

 Protection must be pro-

vided by a residual current

device (RCD) of max.

mA capacity.

 The earthed outlet or the

plug connection to an

extension cable must be

located in an area safe

against flooding.

 Use only extension cables

of sufficient lead cross sec

tion (see "Technical Specifi-

cations"). Unroll cable reels

fully.

 Do not buckle, squeeze,

drag or drive over power

cable and extension cables;

protect from sharp edges.

 Place extension cable so

that it can not get into the

fluid to be pumped.

 Unplug:

 prior to all servicing;

 when persons are in the

swimming pool or garden

pond.

Danger by pump fail-

ures!

 If you notice shipping dam-

age while unpacking, notify

your supplier immediately.

Do not operate the

machine!

 Before each use check the

pump, especially the power

cable and plug for possible

damage. Risk of fatal elec

tric shock!

 A damaged pump must be

workmanlike repaired

before it can be used again.

 Do not attempt to repair the

pump yourself! When

repaired inexpertly there is

a hazard of fluid entering

the electrical parts of the

pump.

Caution!

To avoid water damage,

e.g. flooded rooms, caused

by pump malfunctions or

defects:

 provide for suitable safety

measures such as the fol

lowing:

 alarm or

 collection tank with moni-

toring.

The manufacturer is not liable

for any damage caused by:

 improper use of the pump;

 overloading of the pump

through continous opera

tion;

 failure to operate and store

the pump in a frost-free

environment;

 unauthorised modification

of the pump (repairs to

electrical equipment may

only be carried out by quali

fied electricians!);

 use of spare parts which

have not been tested and

approved by the manufac

turer; or

 use of unsuitable installa-

tion materials (fittings, con-

nection lines etc.).

Suitable installation materi-

als:

 pressure-resistant (min.

10 bar)

 heat-resistant (min.

100°C).

5.1 Discharge hose connec-

tion

The discharge hose is connected either

directly to the discharge port (10), or by

means of the multi-adapter (11) (secure

discharge hose with hose clamps, if nec-

essary).

The check valve's flap (12) must open in

the direction indicated by the arrow. (The

marking "UP" must face the multi adap

tor).

Note:

When using the multi adaptor cut

off any parts nor required, as they

reduce the flow unnecessarily.

5.2 Installation

 Space required approx. 20 cm x

20 cm.

 The pump must not be submerged

deeper into water then stated in the

“Technical Specifications”.



Place pump so that the suction inlet

can not be blocked by foreign objects

(stand on a base, if necessary).

 Ensure sufficient upright stability.

Caution! 

Do not lift pump at cable or dis-

charge hose; both are not designed

for the tensile load by the weight of

the pump.

 Lower pump to the bottom of the

fluid container. Use a strong rope,

fastened to the handle/hanger to

lower the pump.



The pump can also be operated

when suspended by a rope.

Any possibly present air cushion in

the pump can escape through vent

holes when the pump is lowered into

the fluid. Venting generates air bub

bles. This is no fault of the pump but

the effect of automatic venting.

When using the pump for the first

time it may take several seconds

before the air is vented.

 To start the submersible pump plug

power cable in.

 Unplug to stop the pump.

5. Prior to Operation

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo TP 7500 SI in the language / languages: English, German, Dutch, Danish, French, Finnish as an attachment in your email.

The manual is 2,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo TP 7500 SI Manual

Product: