595109

Metabo SM 5-55 Manual

12
Zoom out
Zoom in
Previous page
1/80
Next page
12
ENGLISH
ENG
screwdriver bit: turn the adjusting ring (9) clock-
wise.
•
To decrease the protrusion distance of the
screwdriver bit: turn the adjusting ring (9) anti-
clockwise.
Fine adjustment is performed after the tool is
tested. See section 7.3.
The magazine screw attachment is now ready for
operation.
See illustration on page 3 (please unfold).
7.1
Inserting / Removing a screw strip
(11)
Check whether the screw heads are resting
on the plastic strip otherwise the strip guide
(12) may become damaged and no longer function
correctly.
The screw strip (11) can be inserted from either
side.
- Feed the screw strip (11) through the strip guide
(12).
- Then guide the holes on the strip over the tips of
the teeth on the ratchet wheels (10)
until the
first screw is located in the position in front of
the insertion position
. The screwdriver bit (3)
picks up this screw when the depth stop (7) is
pushed down. For this reason, do not push the
screw strip (11) in too far to avoid wasting any
screws.
To remove the screw strip (11), pull forwards
through the tool. Do not pull the screw strip
(11) back as this may cause serious damage.
7.2 Machine use
We recommend:
- setting the screwdriver to clockwise rotation.
- setting the screwdriver to run continuously.
- Hold the screwdriver with one hand (as shown in
the illustration on page 3). Hold the handle (13)
with the other hand if necessary.
- Hold the tool at right angles to the work surface.
The screw will not be inserted far enough if the
tool is held at an angle that deviates from 90°
even slightly.
- Rest the depth stop (7) on the screwdriver
magazine against the workpiece and apply pres-
sure.
- The screw moves to insertion position and is
screwed into the workpiece.
- If the coupling on the screwdriver audibly disen-
gages, remove the magazine screw attachment
from the workpiece.
7.3 Precision screw depth adjustment
The screw depth (or countersink depth) is adjusted
by turning the adjusting ring (9).
- Insert a screw to test the tool settings.
- If necessary, fine adjust the countersink depth by
turning the adjusting ring (9):
•
To increase the protrusion distance of the
screw head: turn the adjusting ring clockwise.
•
To decrease the protrusion distance of the
screw head: turn the adjusting ring anticlock-
wise.
7.4 Changing the screwdriver bit (3)
Always use genuine Metabo screwdriver bits (see
section 10 Accessories).
If the screwdriver bit is worn/damaged or a
different fastening system is used (Philips,
Pozidriv, Torx or Square Drive), the screwdriver bit
must be changed.
- Detach the screwdriver magazine with adapter
(2) from the screwdriver (do not slacken the
clamping screw (1)).
- Remove the screwdriver bit (3) (read the screw-
driver Operating Instructions).
- Insert a new screwdriver bit (3) (read the screw-
driver Operating Instructions)
- Attach the screwdriver magazine with adapter (2)
to the screwdriver again.
See illustration on page 3 (please unfold).
Problems:
•
Countersink depth: see points b), d), e), i)
•
Seized screws: see point b)
•
Missing screws: see points c), g)
•
Screws do not move: see points a), d)
•
Sliding piece (6) not fully inserted: see point h)
• General: see points a) to i)
Troubleshooting:
a) Always set the screwdriver to CLOCKWISE
ROTATION (FORWARDS).
b) Make sure that the depth stop (7) is adapted to
the length of the screws used.
c) The screwdriver bit (3) must be the correct
length. Always use genuine Metabo screwdriver
bits (see section 10 Accessories).
d) If you are working with Philips screws, make
sure you use a Philips screwdriver bit. If you are
working with Pozidriv screws, make sure you
7Use
8 Troubleshooting
17026885_1211 SM 5-55.book Seite 12 Mittwoch, 14. Dezember 2011 11:28 11
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo SM 5-55 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo SM 5-55 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info