Manual Metabo SM 5-55 (page 11 of 80) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

595109

Zoom out

Zoom in

1/80

ENGLISH

ENG

Always attach the depth stop and supplied handle

with strip guide before starting work.

When dismantling the screwdriver magazine,

remember that the sliding piece is spring-loaded.

Dismantle with care so that the sliding piece does

not eject from the tool and strike people or objects

in the direct vicinity.

Only use screw types and dimensions that are

listed in the Technical Specifications and make

sure that they are suitable for the material being

processed.

Always use genuine Metabo screwdriver bits and

replace bits immediately if they become worn or

damaged. (see section 10 Accessories).

Switch the screwdriver to "Clockwise" rotation.

We do not recommend removing screws ("Anti-

clockwise" rotation) with the screwdriver magazine

attached.

Before removing screws, do not detach the

complete screwdriver magazine from the screw-

driver as the mounting is not designed for frequent

removal and reattachment and will wear prema-

turely.

Instead, slacken the clamping screw (1) and then

detach the screwdriver magazine from the adapter

(2). Then remove the screw. Slide the screwdriver

magazine over the screwdriver bit (3) on the

adapter (2) and push against the adapter (2). Align

the screwdriver magazine on the screwdriver

accordingly. Tighten the clamping screw (1) again.

Switch on the screwdriver before inserting any

screws to improve machine handling.

See illustration on page 3 (please unfold).

1 Clamping screw

2 Adapter

3 Screwdriver bit

4 Standard screwdriver depth stop

5 Quick-release screwdriver coupling

6 Sliding piece

7Depth stop

8 2 screws for depth stop adjustment

9 Adjusting ring (screw depth/countersink

depth)

10 Ratchet wheels

11 Screw strip

12 Strip guide

13 Handle

For cleaning, maintenance (see page 4):

14 Screw (with roller)

15 Spring guide

16 Pressure spring

17 Crosshead screw

18 Pin

19 Ratchet wheel unit

See illustration on page 3 (please unfold).

6.1 Attaching the magazine to the screw-

driver

- Remove the standard depth stop (4) from the

screwdriver (read the screwdriver Operating

Instructions).

- Insert the screwdriver bit (3) into the quick-

release coupling (5) on the screwdriver (read the

screwdriver Operating Instructions).

- Attach the screwdriver magazine with adapter

(2) to the screwdriver bit (3) on the screwdriver.

Note:

the adapter (2) can be attached to the

screwdriver in 4 positions (rotated in 90° incre-

ments). Slacken the clamping screw (1) to align

the screwdriver magazine parallel to the screw-

driver. Tighten the clamping screw (1) again.

6.2 Adjusting the depth stop (7)

The numbers on the depth stop (7) correspond to

the screw lengths (mm) that the tool is capable of

inserting.

The depth stop (7) must be adapted to the

length of the screws being inserted.

- Slacken the two screws (8) and adjust the depth

stop (7) according to the length of the screws

you wish to insert.

- The depth stop (7) is set correctly when the

number indicated (e.g. "35") is the same as the

screw length (8).

- Tighten the two screws (8) again.

6.3 Presetting the screw depth

The screw depth must be adjusted every time the

screw size changes and the position of the depth

stop (7) is modified.

- Push in the depth stop (7) up to the stop and

hold in this position.

- The tip of the screwdriver bit (3) should protrude

approx. 3 mm beyond the depth stop (7).

- If necessary, adjust the screw depth by turning

the adjusting ring (9):

•

To increase the protrusion distance of the

5Overview

6 Commissioning

17026885_1211 SM 5-55.book Seite 11 Mittwoch, 14. Dezember 2011 11:28 11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo SM 5-55 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,94 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo SM 5-55 Manual

Product: