451417

Metabo BW 600 Manual

14
Zoom out
Zoom in
Previous page
1/52
Next page
14
ENGLISH
5. Remove the cut off piece from the
feed rocker – make next cut...
6. If no further cutting is to be done
immediately afterwards, turn
machine OFF.
A
Danger!
Prior to all servicing:
− switch machine OFF;
− wait for saw blade to stop;
− unplug power cable;
• Check that all safety devices are
operational again after each service.
• Replace damaged parts, especially
safety devices, only with genuine
replacement parts since parts not
tested and approved by the equip-
ment manufacturer can cause
unforeseeable damage.
• Repair and maintenance work other
than described in this section should
only be carried out by qualified spe-
cialists.
7.1 Saw blade change
A
Danger!
Directly after cutting the saw
blade can be very hot – burning haz-
ard! Let a hot saw blade cool down.
Do not clean the saw blade with com-
bustible liquids. Risk of injury, even
with the blade at standstill. Wear
gloves when changing blades.
When assembling, observe the direc-
tion of rotation of saw blade and outer
blade flange!
1. Loosen screw fitting (17) of the stop
llimiter and lower the feed rocker
(18) carefully.
2. Hold outer blade flange (19) with
assembly wrench and loosen the
arbor bolt (23) (R.H. thread!).
3. Remove arbor bolt (23), spring lock
washer (22) and outer blade flange
(21) from the saw spindle.
4. Take the saw blade (20) off the saw
spindle.
5. Clean clamping surfaces of:
− saw spindle,
− inner blade flange,
− saw blade,
− outer blade flange,
− washer,
− arbor bolt.
A
Danger!
Do not use cleaning agents
(e.g. to remove resin residue) which
could corrode the light alloy compo-
nents; this can have an adverse effect
on the machine's stability.
Do not clean the saw blade with com-
bustible liquids.
6. Install inner blade flange (19) and
fresh saw blade (20), observing the
direction of rotation.
A
Danger!
Use only saw blades conform-
ing to the technical specifications and
EN 847-1 – parts of unsuitable or
damaged saw blades may be hurled
away explosive-like.
Do not use:
− saw blades made of high speed
steel (HS or HSS);
− saw blades with visible damage;
− cut-off wheel blades.
A
Danger!
− Mount saw blade only using gen-
uine parts.
− Do not use loose-fitting reducing
rings; the saw blade could work
loose.
− Saw blades have to be mounted
in such way that they do not wob-
ble or run out of balance and can
not work loose during operation.
7. Put on the outer blade flange – (21)
the key on the saw spindle must
engage in the groove of the outer
blade flange!
8. Put on the washer (22), then screw
arbor bolt (23) in (RH thread!) and
tighten fully.
A
Danger!
− Do not extend arbor bolt tighten-
ing wrench.
− Do not tighten arbor bolt by hit-
ting on the assembly wrench.
− After tightening the arbor bolt,
remove both assembly wrenches.
9. Lift the feed rocker (18) back to its
starting position.
10. Reinstall the screw fitting (17) of the
stop limiter.
7.2 Saw storage
A
Danger!
Store saw so that
− it can not be started by unauthor-
ized persons, and
− nobody can get injured.
A
Caution!
Do not store saw unprotected
outdoors or in damp environment.
3
Note:
Always install the transport brace
before transporting the saw.
To keep the saw blade from rusting,
spray with Cleaning and Maintenance
Spray (optional accessory) before stor-
ing it for a longer time.
7.3 Maintenance
Every 50 hours of operation
Check all screwed connections, tighten if
necessary (Rocker and rocker stop must
remain movable).
Check saw blade for firm seat, wear and
sharpness.
Remove any deposits that may have
build up inside the saw blade cover.
7. Care and maintenance
17
18
23
22
19
21
20
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo BW 600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BW 600 in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 3,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info