451417

Metabo BW 600 Manual

12
Zoom out
Zoom in
Previous page
1/52
Next page
12
ENGLISH
A
Hazard generated by modifica-
tion of the machine or use of parts
not tested and approved by the equip-
ment manufacturer!
Use only parts approved by the equip-
ment manufacturer. This applies particu-
larly to:
− Saw blades (see "Technical specifi-
cations" for stock numbers);
− Safety devices (see "Spare parts
list" for stock numbers).
Do not change any parts.
A
Hazard generated by machine
defects!
Keep machine and accessories in good
repair. Observe the maintenance
instructions.
Before any use check machine for possi-
ble damage: before operating the
machine all safety devices, protective
guards or slightly damaged parts need to
be checked for proper function as speci-
fied. Check to see that all moving parts
work properly and do not jam. All parts
must be correctly installed and meet all
conditions necessary for the proper
operation of the machine.
Damaged protection devices or parts
must be repaired or replaced by a quali-
fied specialist. Have damaged switches
replaced by a service centre. Do not use
this machine if the switch can not be
turned ON or OFF.
Keep handles free of oil, grease and
resin.
3.3 Safety devices
Motor protection
The electronic motor protection stops
the motor by overcurrent detection,
should the motor be locked (e.g. by a
jamming saw blade).
No-voltage release
The no-voltage release feature prevent
the machine from starting up when the
power is restored after a power failure.
Motor brake
The motor brake brakes the saw blades
after the machine has been turned OFF.
With an intact motor brake the post-run-
ning of the saw blade shall not exceed
10 seconds.
Feed rocker
The feed rocker allows for a safe feeding
of the logs to be cut. When the feed
rocker is released it must automatically
return to its starting position.
Blade guard
During operation the blade guard must
always be installed. It must not show any
signs of damage. The blade guard's
extension arm must automatically return
to its starting position.
3.4 Symbols on the machine
A
Danger!
Disregard of the following
warning could lead to severe per-
sonal injury or material damage.
Wear hearing pro-
tection.
Use this machine
out of doors only.
SP 600 x 2.8 x 30 Max ∅ saw blade:
600 mm
Saw blade thick-
ness: 2.8 mm
∅ Sawblade arbor
bore: 30 mm
n max. 2500 rpm Max. saw blade
speed
Z=56 KV Number and con-
figuration of teeth:
56 combination
multiple teeth
Information on the nameplate:
• Robust, powder-coated welded
steel construction for maximum tor-
sional resistance at low weight.
• Hinged wheel set for unproblematic
relocating.
• Powerful, splash-proof three-phase
motor.
5.1 Machine installation
A
Danger!
This machine shall only be
operated at a location meeting the fol-
lowing conditions:
− outdoors
− level, non-slip ground
− all four of the machine's legs
must be able to stand firmly on
the ground.
1. Transport the machine on the pallet
to a suitable location.
2. Remove packing and enclosed
parts.
3. Remove the screws holding the
machine on the pallet.
4. Lift machine off the pallet.
5. Remove transport brace (15).
3
Note:
Always install the transport brace
before transporting the saw.
5.2 Mains connection
B
Danger! High voltage
Operate the machine only on a
power source matching the following
requirements (see also "Technical
specifications"):
− Outlets with neutral wire, being
properly installed, earthed and
tested.
− Mains voltage and frequency
must conform with the data
stated on the machine's name-
plate.
− Fuse protection by a residual cur-
rent device (RCD) of 30 mA fault
current sensivity.
(8) Manufacturer
(9) Serial number
(10) Machine designation
(11) Motor specifications (see also
"Technical specifications")
(12) Year of make
(13) CE mark – this machine meets
the EC directives as per declara-
tion of conformity
(14) Dimensions of permissible saw
blades
4. Special product features
9
10
11
12 13 14
8
5. Transportation and
installation
15
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo BW 600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BW 600 in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 3,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info