609971
8
Zoom out
Zoom in
Previous page
1/17
Next page
12 13
Drive/Distributor
sectional view
Distributor cover
Distribution,
Fan Jets
Center connection,
Fountain Jet
Flap and spring
Sectional view without gear
Distribution,
Ring Jets
Bore Ø 6 mm
towards
pump
Distribution,
Bell Jets
Drive/Distributor
topview
Repair work
Pull out mains plug of the pump and the lighting before all repair and maintenance work.
Opening of the waterworks
Unscrew the bell jets and turn the waterworks upside down (jets downwards).
In order to prevent the jets from being scratched, it is advisable to use a soft underground (foam material).
Turn the 6 screws with hexagonal recessed holes on the outside and the hexagon cap screw in the middle
out of the base plate of the waterworks.
Thereby it is possible to do all repair work.
Failure of a water pattern or permanent running of one water pattern:
Phase 1: Bell jets and fan jets
Phase 2: Fan jets and ring jets
Phase 3: Ring jets and fountain jet
Phase 4: Fountain jet and bell jets
Mechanical load and natural wear
and tear may result in a failure of
the component parts of the drive/
distributor.
Please proceed as follows:
1. Open the waterworks
(as described before).
2. Loosen the eight screws on the
distributor cover of the drive and
remove the cover.
3. From the drawing you can learn
which distribution or which center
connection runs to the jet failed.
Draw this element out of its
conductor and check whether:
a) the stainless steel spring,
ap or holder are broken
b) the fl ap closes automatically
c) the closed fl ap fi ts snugly;
do compare with the other fl aps.
4. If there is a damage, we recommend
to replace the complete set,
3 x distribution and 1 x center
connection.
Lighting
In case the lighting has failed, maybe the halogen incandescent lamp in the fl oodlight has exceeded its
service life.
Loosen the two tapping screws beside the defective fl oodlight and pull it out of the appliance together with
the holding ring. By bending up the three hooks, separate the fl oodlight from the holding ring.
Changing of the lamp
Attention! As a replacement, one may use (nearly) all commercial cool-beam, reflectable lamps,
max. 50 watts.
1. Pull out mains plug and secure against reclosing.
2. Hold tight the fl oodlight casing and unscrew the fl oodlight ring anticlockwise.
3. Remove the fl oodlight glass.
4. Remove the lamp from the casing and remove the ceramic socket.
5. Before re-assembling the fl oodlight, please clean the glass and the sealing ring.
Do avoid using scouring liquids or any sharp instruments.
The sealing ring is fi tted to the casing and should not be removed.
6. Replace the lamp, put it again in the socket and re-insert it into the casing.
7. Place the glass on the sealing ring which is provided on the casing, put back the fl oodlight ring and screw
it clockwise.
For re-assembling the complete fl oodlight on the appliance, clip the holding ring again to the fl oodlight,
re-insert both pieces into the “Versailles” and tighten with the 2 tapping screws.
Taking care of your waterworks in winter
Protect the waterworks against frost.
Take the appliance out of the water in autumn and store it in a frost-proof room during the winter months.
Guarantee conditions
This Water Display «Versailles mini» comes with a 24-month guarantee ( oodlight lamp excluded) that
is effective from the date of delivery. The invoice will be the proof of the date. In case of damages due to
defects in material or manufacturing, we shall either do a free repair during the guarantee period or replace
the damaged part, the choice being ours’.
Damages that occur due to installation and operating errors, lime deposits, insuffi cient care, frost action,
normal wear and tear or improper repair attempts will not come under this guarantee. The guarantee will not
be valid in case of modifi cations to the apparat, e.g. cutting off the line connection or the line cord. We will
not accept responsibility for consequential damages resulting from breakdown of the apparat or improper
operation.
When making use of the guarantee, please send us the apparat, along with the corresponding invoice, free
of charge via the specialist dealer who sold you the apparat.
Floodlight ring
Glass
Lamp
Socket
Sealing ring
Floodlight casing
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Messner Versailles at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Messner Versailles in the language / languages: English, German, French as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Messner Versailles

Messner Versailles User Manual - English, German, Dutch, French, Italian, Portuguese, Spanish - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info