531599
13
Zoom out
Zoom in
Previous page
1/27
Next page
Operation Theory Page 11
MD 1998LE (B1997PNST)
2. In protection mode or out-of-range situation, HUNLock will send 5 V pulse to saturate Q706, then pin 8
of I902 will be low state and open Q509, so G1 will go down to -140V. During the mode change, Mute
acts as same as HUNLock’s.
3. The brightness is controlled by CPU, pin 27 and pin 28 comes into pin 20 and pin 21 of I501, DC level can
be changed by I
2
C bus from 0~5V of D/A output at pin 23 of I501, high voltage causes high current to get
brighter raster, low voltage gets lower brightness.
3-4 Power Supply Section
3-4-1 AC Rectifier
The circuit can accept 90 V to 264 V AC input through D801 bridge diode and C810 filtering to get DC 126
V~364 V for power conversion in T805.
3-4-2 Line Filter
It consists of L801, L802, P801A, C803, C804, C805, C806, C807, C871, C80A, C80C, C80E, T801 and
T802 and meets EMI regulation.
3-4-3 PFC
It consists of T804, Q814, D807, I804 and other auxiliary components. It is similiar to Booster circuit. The
working voltage is provided by D815, C821, R825, C819 and ZD810, but it is not working in Stand-by,
Suspend and Off modes. The output voltage C810 is 180 V~380V DC and generated through input
voltage C816 step up. The maximum voltage is decided by R826 and R827, while the minimum voltage is
decided by C817. In the meanwhile, it will get a similiar to input voltage waveform of input current to
acquire a good PF value.
3-4-4 Power LED Status
1. The LED has 3 leads common cathode with green and amber color for different power saving states. It
is controlled by CPU.
2. Normal : Green light
Amber LED is off because CPU pin 17 is high and pin 18 is low, only green LED is turned on.
3. Standby / Suspend : Yellow light
CPU pin 17 and pin 18 are low, then green and amber LED are turned on. That is yellow.
4. Off Mode : Amber light
CPU pin 18 is high and pin 17 is low, then green is off and amber is on.
3-4-5 Auto Degaussing
When SMPS works, the 6.6 V power source is applied to Q801 and CPU let Q801 turn on a few seconds,
then drive the armature of RL801 to perform the degaussing function.
3-4-6 PWM Control
1. Start Up
The I802 gets power from C874, C841, R834, ZD807, D802, C859, R806 and pin 7 voltage reaches 9 V
for starting up. The I802 starts oscillation at 20 kHz, sawtooth on pin 4 and pin 6 output to drive Q802/
T805. Once Q802 switches on, D812, C840 set up an 17 V to keep I802 working through D828 auxiliary
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Medion MD1998LE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Medion MD1998LE in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info