531599
12
Zoom out
Zoom in
Previous page
1/27
Next page
Page 10 Operation Theory
MD 1998LE (B1997PNST)
controllable by I
2
C bus. SDA and SCL signals coming from microprocessor feed to pin 19 and pin 18 to
control all functions.
3-3-1Horizontal Section
1. The oscillator is driven by the currents in R424 and R423. The minimum oscillator frequency is determined
by R424 and the maximum frequency is determined by R423.
2. Horizontal sync goes into pin 15 through R314. And horizontal flyback pulse goes into pin 1 through C455,
C437, R404, C458, R40E and bypass filter C401 from Vcp of Q424 collector for AFC loop.
3-3-2 Horizontal O/P Section
1. Horizontal driver (pin8) signal is sent to Q402 via R496, C451.
2. Signal from Q427 direct drive T403, through R493 (shunt with R4A4, R40F, R40G) and L405 to horizontal
output transistor Q424.
3-3-3 Vertical Section
1. Vertical sync signal from micro controller is connected to pin 14 through R313.
2. The free running frequency is determined by R319 and C312.
3-3-4Vertical O/P section
1. The differential output currents from pin 13 of Vout1 and pin 12 of Vout2 can be directly coupled to the
vertical deflection booster pin 1 and pin 2 of TDA8351.
2. The TDA8351 has two output stages which are current driven in opposite phase and operate in combination
with the deflection coil in a full bridge configuration.
3-3-5 E-W/Trapezoid and H. Size Controls
1. The B+ driver for step down circuit is from pin 6, it provides 20~80% duty cycle outputs according
to H-frequency.
2. The E/W / Trapezoid and H-size controls are through B+ modulation at I401 TDA4856. The EW output
signal is from pin 11, it’s not tracking with H-frequency.
3-3-6 X-Ray Protection
1. To avoid X-ray hazard, a DC voltage generated at pin 3 of FBT and rectified by D108, C121 is divided by
R126, R129 and C402 filter go into pin 2 of TDA4856.
2. If this voltage is higher than 6.39 V, then TDA4856 will be activated to float HUNLOCK (pin 17), H. DRV
( pin 8), B DRV (pin 6), VOUT1 (pin 12), VOUT2 (pin 13). After that all deflection circuit stop working.
3-3-7G1, Blanking and Brightness
1. The vertical blanking signal comes in two ways. One is from pin 8 of I301 (TDA8351), the other is from
HUNLK (pin 17 of I401). These two positive vertical pulses through Q42A, Q42C, Q42E amplified and
converted into negative pulse and sent to G1 for vertical blanking.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Medion MD1998LE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Medion MD1998LE in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info