684126

McCulloch M51 -140RX Manual

11
Zoom out
Zoom in
Previous page
1/320
Next page
MAINTENANCE
English – 11
General
• Always use genuine accessories.
Maintenance schedule
In the maintenance schedule you can see which parts of
your machine that require maintenance, and with which
intervals it should take place. The intervals are calculated
based on daily use of the machine, and may differ
depending on the rate of usage.
*See instructions in the section "Machine’s safety
equipment".
General inspection
• Check that nuts and screws are tight.
External cleaning
• Brush leaves, grass and the like off of the lawn mower.
• Do not use a high pressure washer to clean the
machine.
• Never flush water directly on the engine.
• Clean the air intake on the starter. Check the starter
and starter cord.
• When cleaning under the cutting deck, turn the
machine with the spark plug upwards. Empty the fuel
tank.
Oil level
The lawn mower should stand on flat ground when you
check the oil level.
• Unscrew the oil cap, clean the dipstick located on the
cap and insert the cap again without screwing it down.
Check the oil level on the dipstick.
• If the oil level is low, fill using engine oil up to the upper
level on the dipstick.
Cutting equipment
• Check the cutting attachment for damage or cracks. A
damaged cutting attachment should always be
replaced.
• Always ensure the cutter is well ground and balanced
correctly.
Replacing the blades
Dismantling
• Unscrew the bolt holding the cutter.
• Remove the old blade. Make sure the blade bracket is
free of damage. Also check that the cutter bolt is
undamaged and that the engine shaft is not bent.
Assembly
• Make sure the cutter centres correctly on the shaft.
!
WARNING! The user must only carry out
the maintenance and service work
described in this Operator’s Manual.
More extensive work must be carried out
by a service workshop.
Prevent unintentional starting by
removing the ignition cable from the
spark plug.
The life span of the machine can be
reduced and the risk of accidents can
increase if machine maintenance is not
carried out correctly and if service and/or
repairs are not carried out professionally.
If you need further information please
contact your nearest service workshop.
CAUTION! When the machine is tilted, make sure the air
filter always is placed in the highest position.
Before starting
Weekly
maintenance
Monthly
maintenance
General inspection Spark plug Air filter
External cleaning Muffler* Fuel system
Oil level
Cutting equipment
Cutting cover*
Adjusting the
clutch wire
Engine brake
handle*
CAUTION! The blades should be balanced after
sharpening. Balancing, replacing or sharpening the
blades should be conducted by a service workshop.
Damaged blades should be replaced when hitting
obstacles that result in a breakdown. Let the service
centre assess whether the blade can be sharpened or
must be replaced.
!
WARNING! Always wear heavy-duty
gloves when servicing and maintaining
the cutting equipment. The cutters are
very sharp and cuts can occur very
easily.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch M51 -140RX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch M51 -140RX in the language / languages: All languages as an attachment in your email.

The manual is 10,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info