634676

Mc crypt DJ-60-PC Manual

41
Zoom out
Zoom in
Previous page
1/89
Next page
41
8. Initial operation
e) Listening-in/pre-listening
Turn the LEVEL control (11) as far as it will go to the left („0“ position) before plugging in,
unplugging or putting on the headphones or switching the mixer on or off. Otherwise you risk
damage to your hearing through excessive volume from the headphone output.
• Use the CUE/PGM control (10) to specify whether you want to hear the output signal or the input signal from the
mixer’s individual channels on the headphones.
• Move the CUE/PGM control (10) into the „PGM“ position to reproduce the output signal (MASTER signal) on the
headphones.
• Move the CUE/PGM control knob (7) into the „CUE“ position to reproduce the input signal of the channel which
has been activated using the CH A/CH B pre-listening switch (6) on the headphones. This position facilitates what
is referred to as „pre-listening“, i.e. you can hear the input signal without it being reproduced via the connected
amplifier. This will enable you to find the correct start point – for example, when cross-fading or mixing.
f) Cross-fading/mixing
• You can use the cross-fader (8) to cross-fade/mix between the signals from the two channels.
• When the cross-fader (8) is actuated, one channel is faded out (becomes quieter) and the other channel is faded
in (becomes louder) at the same time. In the central position, both fader channels are reproduced equally.
• You can influence the cross-fader’s (8) control characteristics with the XF CURVE switch (13). The SHARP
position gives you a sharper control, which is suitable when „scratching“. The GRADUAL position provides softer
control, which is good for smooth cross-fading.
• You can switch the direction that the cross-fader (8) operates in (i.e. reverse the channel allocation) with the RIV
X-FADER CONTROL switch (14). In the NORMAL position, channel A is on the left of the cross-fader (8). In the
REVERSED position, channel B is on the left of the cross-fader (8).
g) Using the DJ microphone
• If you want to make an announcement, talk into the microphone and use the MIC control (4) to set the volume.
• You can influence the sound of the microphone with the sound controls (5) HI and the LOW knob under the MIC
control (4).
• Once you have made your announcement, turn the MIC control (4) back to position „0“ to prevent any distortion
or background noise from being output.
… 41 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mc crypt DJ-60-PC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mc crypt DJ-60-PC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info