650496
77
Zoom out
Zoom in
Previous page
1/85
Next page
76 77MAXDATA SN 40 M1 – User GuideProtecting Local Disks
76 77MAXDATA SN 40 M1 – User GuideProtecting Local Disks
7. When you are prompted to restart the computer, click “Yes”.
You do not have to restart your computer immediately, but you cannot access the recovered
disk or partition until you do.
As soon as you restart the computer, you must start Intel
®
Client Backup and Recovery and
back up the recovered disk or partition manually (as described in “Manually Backing up Your
Disk” on page 72) to resume protection. In addition, if you recovered a partition and any other
partitions on the same disk were protected, you must manually back up those partitions as
well.
Recovering a System Disk or Partition
To recover a system disk or partition using the recovery CD:
1. Using the appropriate procedure for your system, configure the computer to boot from the CD-
ROM drive.
2. Insert the recovery CD into the CD-ROM drive.
When responding to the prompts, use the arrow keys to highlight the desired item, use the
space bar to select or clear options (an X appears in the brackets when the option is selected),
and press Enter to make your selection. You can also tab between fields.
Arrow keys Navigate between items and
highlight items
Space bar Select or clear options
Enter Make a selection
Tab Move between fields
3. When the hardware list appears, use the arrow keys to select the network interface card (NIC)
that you want to use when recovering the data, and then select “Next”.
In most cases, there will be only one NIC, and you can simply select “Next”.
This screen displays only the NICs on this system that are supported by Client Backup and
Recovery. If no NICs appear on this screen, you might need to install an appropriate network
driver. Select “Load Driver”, select the location from which you want to install the driver
(“Load From System” for the local hard disk, “Load From Floppy” for a floppy disk drive, or
“Load From CDROM” for a CD-ROM drive), insert the disk in the drive (if loading from a floppy
disk or CD-ROM), and respond to the prompts. For information about obtaining the appropriate
driver, contact your vendor.
To see a complete list of the detected hardware, select “Rescan”. When you are done viewing
the list, select “OK”.
4. Review the settings for your NIC and select “Next”.
The recovery CD obtains the IP address to use from your DHCP server. If the displayed
settings are not the ones you want to use, or if no IP address is displayed, use the arrow
keys and space bar to select “Config” and then type in the desired IP address (for example,
“192.168.0.101”) or subnet mask. (If you make a mistake typing either the IP address or
subnet mask, select “Disable” to clear the displayed information.) Then select “OK” and select
“Next”.
5. In the “Client Name” field, enter the full computer name of this computer in all capital letters.
If you don’t remember the full computer name, access the Manager (as described in
“Accessing the Manager” on page 15) and click “Backups” in the navigation bar. In the
“Protected disks” list, the “Computer Name” column lists the computer name of each
computer that has backed up disks to the storage system.
77


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maxdata SN 40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maxdata SN 40 in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info