171513
28
Zoom out
Zoom in
Previous page
1/45
Next page
28 Server Board Features
Callout LED Function
H. System fan 5 fault LED This LED indicates a fault has occurred with system fan 5. See
your server chassis documentation for instructions to replace the
fan.
I.
J.
K.
L.
M.
N.
O.
P.
DIMM A1 fault LED
DIMM A2 fault LED
DIMM B1 fault LED
DIMM B2 fault LED
DIMM C1 fault LED
DIMM C2 fault LED
DIMM D1 fault LED
DIMM D2 fault LED
These LEDs indicate a fault has occurred with the FBDIMM
installed in the corresponding socket. Replace the faulty
FBDIMM.
Q. +5-volt standby LED This LED is green whenever AC power is applied to the system.
The system does not need to be powered on in order for this
LED to be on.
R.
S.
Processor 2 fault LED
Processor 1 fault LED
These LEDs indicate a fault has occurred with the processor
installed in the corresponding socket. Replace the faulty proc
-
essor.
T.
U.
Processor 2 fan fault LED
Processor 1 fan fault LED
These LEDs apply only to server systems that use an active
heatsink. These LEDs indicate a fault has occurred with fan that
is installed on the heatsink for the corresponding processor.
Replace the faulty unit.
RAID Support
The server board provides an embedded SATA controller that supports both 1.5 and 3.0 Gbps data
transfer rates.
The Drive configuration options on the Advanced | ATA Controller BIOS setup page allow different
configurations. When the “Onboard SATA Controller” is enabled, the “SATA Mode” option can be
set to either “Legacy” or “Enhanced”.
“Legacy” supports four disk drives and does not provide RAID support.
“Enhanced” supports six disk drives and is required for RAID configurations.
When the enhanced mode is selected, you can choose to enable “AHCI Mode” or “Configure SATA
as RAID”. The latter enables the Intel
®
Embedded Server RAID Technology II feature that provides
RAID modes 0, 1, and 10.
Hardware Requirements
Processor
One or two Dual-Core Intel
®
Xeon
®
processors 5000 sequence are supported.
Memory
The Platinum 3200 I Server Board provides eight DIMM sockets:
Channel A, nearest to the center of the server board, consists of DIMM sockets A1 and A2
Channel B consists of DIMM sockets B1 and B2
Channel C consists of DIMM sockets C1 and C2
Channel D consists of DIMM sockets D1 and D2
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Maxdata platinum 3200 i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Maxdata platinum 3200 i in the language / languages: English as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info