545558
18
Zoom out
Zoom in
Previous page
1/133
Next page
SFX SERIES USER’S GUIDE
Rev 2.2 16
After processing an input line (or after return is pressed on a blank line), the interface will display the “IDC>”’ prompt on
the terminal. You can type GetCommands at this prompt to obtain a list of available commands. Use upper and
lower case for the command as shown.
The terminal interface will remain active until an exit command is issued to logout, or the timeout period of five minutes
has been reached.
A separate International Datacasting Application Note is provided with details on the specific commands for the
Terminal Interface. Please proceed to Chapter 3 for more information on obtaining application notes.
Controlling the Receiver with the Web GUI
All accessible functions within the satellite receiver can be controlled using the Web Graphical User Interface (GUI).
The receiver acts as a web server in this case, serving out GUI pages to a PC with a browser. Communications
between the browser PC and the receiver is via a LAN connection to one of the Ethernet ports on the rear panel,
generally using the https protocol (SSL is used and the secure link is always enabled).
The Web GUI is compatible with the following web browsers:
1. Internet Explorer V5.0 or later, running under Windows® ‘95, ’98, 2000 or Windows NT or XP OS.
2. Mozilla V0.98 or later, running under Linux OS.
3. Firefox V1.5 or greater under Windows/Linux/MAC OS.
The Web GUI is best used with browsers that are displayed at a resolution of 1024 x 768 or greater, although 800 x
600 resolution is sufficient. However, at 800 x 600 resolution you may need to use the scroll bars more often.
Typically, an Ethernet crossover cable is used in the field when the receiver is being aligned to the satellite signal and a
point-to-point connection is required between the receiver and the browser PC. To communicate between the satellite
receiver and the browser PC, it is necessary that the IP address of the customer’s computer be set to the same subnet
as the receiver. The factory default IP address of the eth0 interface is 192.168.0.1 and the eth1 interface is
192.168.1.1. Typically, you will have to use the SetIP command in the Terminal Interface, or use the LCD control
panel to set the IP address to another value. If you do not know the IP address of the receiver, you can discover it by
using the GetIP command in the Terminal Interface, or you can view it through LCD control panel.
When the browser PC and the receiver are connected together via a hub or switch in a LAN configuration (typically
using Ethernet “straight through” cables), the same rule as above, applies.
If the browser PC and the receiver are on different LANs connected by the Internet, communications between the two
can only be made if the receiver IP address is known. Typically, the satellite receiver would be set up on its LAN with a
gateway to the Internet.
Once the receiver is set up with an IP address that is known, you can access the receiver by typing the IP address in
the Address line of the browser. The Web browser will default to port 443 (SSL), so only the IP address is required in
the Address line. If there is no demo content in the receiver (e.g. customized web page accessed in the clear via port
80), then this port will be forwarded through port 2100 (secure access). If your connection is successful, you will be
required to login to the receiver, as shown in the example Internet Explorer login page in Figure 1- 4 below.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Max SFX Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Max SFX Series in the language / languages: English as an attachment in your email.

The manual is 4,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info