797866
20
Zoom out
Zoom in
Previous page
1/95
Next page
4. Remove the Lid. Ensure the Inner Lid gaskets are in place. Place the Inner Lid Outer Gasket
around the outside of the Inner Lid and the Inner Lid Center Gasket in the center hole. Make sure the
float valve and gasket are in place in the lid (see ASSEMBLY INSTRUCTIONS).
5. Place the Inner Pot in the Base. Pour 2 cups (473 mL) of water in the Inner Pot.
6. Attach the Power Cord to the Unit Base first, and into wall outlet (see the ATTACHING THE
POWER CORD)a. When the Unit is first plugged in, “---- ” will appear on the LED Display. The Unit is
automatically “ON” when plugged in.
7. ATTACHING LID: With the LCD Display facing you, placing the Lid on the Unit, aligning the Lid
Position Mark with the Open Mark (see Fig. C). Twist the Lid counterclockwise about 30° (see Fig.
D). When the Lid is locked, the Release Switch will move to the Closed position.
8. The Magnetic Safety Sensor assures Lid is properly closed before the Unit can pressurize. If Lid is
not on correctly when starting a cooking cycle, a beeping sound will occur and the word “LID” will
appear on the display that indicate Lid is not fully closed.
9. Once Lid is properly closed, select the Canning Button on the Panel. Turn the Program Dial to the
left to select the Low setting and then press the Program Dial to confirm the setting, and will set a
10-min. cooking time automatically. The LCD Display will turn orange while pressure builds in the
Unit and will turn red when the pressure level is achieved.
CAUTION: DO NOT ATTEMPT TO OPEN LID WHEN LCD DISPLAY IS ORANGE OR RED.
10. SAFELY RELEASE PRESSURE: Once the cycle is done, the Unit will beep. Press the Cancel
Button and move the Release Switch from the Closed to the Open position and release. Allow all
pressure to escape from cooker. You will notice a slight incline of the Pressure Release Valve while
pressure is being released.
WARNING: Keep body (face, arms, torso) away from Pressure Release Valve area when
operating the Release Switch to avoid being exposed to the steam released from the valve.
Follow these safety precautions when releasing pressure to prevent serious injury.
11. Allow the water in Inner Pot to cool. Remove and empty the Inner Pot. Rinse and towel dry.
WARNING: DO NOT LIFT BASE TO REMOVE CONTENTS from Inner Pot. Do not lift the Inner Pot
from the Base when contents are hot.
NOTE: Do not use metal utensils in the Inner Pot.
WARNING: PREVENT BURNS! DO NOT TOUCH STAINLESS STEEL EXTERIOR. ONLY USE
BLACK HANDLE ON LID TO OPEN. CONTENTS IN COOKER ARE HOT. ALWAYS OPEN LID
AWAY FROM FACE AND BODY.
FIG. ix
FIG. x
ASSEMBLY INSTRUCTIONS
PRESSURE RELEASE VALVE ASSEMBLY
NOTE: Do not attempt to assemble or disassemble the Pressure Release Valve when the Power
Quick Pot is in use.
INSTRUCTION FOR USE
A. PREPARING FOR USE
CHECK PARTS & ACCESSORIES
1. Before using, remove all the parts and accessories from package and ensure all parts have been
included before discarding any packaging materials. Remove all packing materials such as plastic
film, cardboard, and stickers on the Pressure Release Valve and Condensation Collector (see
PARTS & ACCESSORIES).
2. CLEAN INSIDE: Remove the Inner Lid from Lid by pulling metal knob. Remove Rubber Gaskets
from Inner Lid (see INNER LID ASSEMBLY). Wash Inner Lid, Rubber Gasket, Inner Pot, and other
loose accessories with warm, soapy water, rinse and dry.
NOTE: Ensure to replace Rubber Gaskets (see CHANGING THE INNER LID RUBBER GASKETS
AND FLOAT VALVE ASSEMBLY sections) before reinstalling Inner Lid.
CONDUCT TEST RUN WITH WATER ONLY
1. To check that the Unit will operate properly, it is recommended to periodically check its operation
without cooking food.
2. Place the One Touch Quick pot on a clean, flat surface.
3. Attach Condensation Collector to side of the Unit by sliding it into the slots (see Fig. A).
NOTE: The Condensation Collector may be preas- sembled.
• Pull to remove the Pressure Release Valve (see Fig. ix).
• Ensure that the Pressure Release Valve and holes are
not blocked by food or debris. If blocked, wash out or use
a pin to unblock.
• Look at the clip on the underside of the Pressure
Release Valve (see Fig. x). It should not be damaged or
severely bent.
• Press the Pressure Release Valve back into the hole on
the Lid. If the Valve does not insert correctly, it may have a
bent clip.
FIG. A
(Float Valve Rubber Gasket)
FIG. B
(Condensation Collector)
PARTS & ACCESSORIES
LID-TOPVIEW
Your One Touch Quick pot has been shipped with parts and accessories as shown above.Check
everything carefully before use. If any part appears damaged, do not use this product and contact
Customer Service using the number located in the back of this manual.
LID-UNDERSIDE (WITHOUT INNER LID)
FRONT STAINLESS STEEL INNERPOT
EN
Float Valve
Locking Pins
Steam Release Switch
Lid Handle
Pressure Release Valve
LCD Display Base
The Max Fill Line in the
Inner Pot is
represented by “FULL
CUP” on some models
and “MAX” on other
models. DO NOT fill
past the Max Fill Line.
XC
4
5FULL
CUP
38
EN
37
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Masterpro BGMP-9131 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Masterpro BGMP-9131 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info