Manual Mastercraft X30 (page 224 of 285) (English)

614263

224

Zoom out

Zoom in

1/285

Care and Maintenance • 2014 MasterCraft Owners Manual Page 6-31

C A R E A N D M A I N T E N A N C E

Re-Activating the Boat After Storage

Step 1: Removetheducttapefromtheex-

haustaps.

Step 2: Fully charge the battery and in-

stall it in the boat, following all

safetyprecautionsassociatedwith

changing batteries.

IMPORTANT NOTE: Often, batteries

that have been stored over winter will re-

quire re-charging. If the battery is charged

by utilizing a battery charger, use only a

three-stage or more battery charger. It is

important that the operator never turn a

battery charger immediately to “start,” as

the sudden jolt of voltage may cause dam-

age to the electrical system, particularly

control modules for ballast system. Regard-

less of whether it is during the re-activation

process or at any time, care should also be

used in charging the battery.

Step 3: Follow all instructions for reacti-

vating the drive train as detailed

in the engine owner’s manual.

NOTE: Due to the complex na-

ture of the reactivation process,

MasterCraft recommends having

an authorized MasterCraft dealer

perform this function.

Step 4: Ensure that all drain plugs

throughout the boat and drive train

have been reinstalled to avoid un-

wanted intrusion of water.

Step 5: Ifapplicable,reconnectthehoses

toyourheaterorshower.

Step 6: Check the engine compartment

and bilge for signs of nesting ani-

mals.Cleanasnecessary.

Step 7: Check the entire engine system

for uid, oil and coolant levels.

Addasnecessary.

Step 8: Check the entire engine for cracks

orleakscausedbyfreezedamage.

Step 9: Check all hose clamps for tight-

ness. Install the bilge drain plug

and the rear drain plug in boats

equipped with certain types of

ballastsystems.

Step 10:Grease the propeller shaft taper

and install the propeller.

Step 11: Fully re-chargeand re-install the

batteryorbatteries.

Step 12:Performthedailymaintenanceas

noted previously in this Owner’s

Manual.Ifitwasnotdonepriorto

storage, perform the annual main-

tenance as well.

Step 13:If the boat is equipped with the

optional fresh water cooling sys-

tem and was drained for storage,

llthe systemwith freshcoolant

solution per instructions.

Step 14: Check the alignment between the

outputangeonthetransmission

and the propeller shaft ange. If

the maximum feeler gauge that

canclipbetweentheangefaces

at any point is 0.003”, the unit

is properly aligned. If a thicker

gaugecanbeinsertedatanypoint,

the engine must be re-adjusted un-

til proper alignment is obtained.

This should be performed by an

authorized MasterCraft deal-

er’s service department.

Step 15: For all models, with the boat in the

water,cyclethekeyONandthen

OFF two (2) or three (3) times, al-

lowingten(10)secondsbetween

key cycles, before cranking

the engine. This allows the fuel

pumptoprimethefuellines;then

starttheengine.Intheeventthe

engine does not respond, allow

a two-minute cool-down period

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Mastercraft X30 in the language / languages: English as an attachment in your email.

The manual is 5,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Mastercraft X30 Manual

Product: