614263

Mastercraft X30 Manual

225
Zoom out
Zoom in
Previous page
1/285
Next page
Page 6-32 2014 MasterCraft Owners Manual • Care and Maintenance
C A R E A N D M A I N T E N A N C E
for every thirty (30) seconds of
cranking. When the engine res,
keep a close watch over the gauge
readings and check for leakage
and abnormal noises. Keep speeds
lowfortherstfteen(15)min-
utes to allow the engine to reach
normal operating temperatures.
Propeller Maintenance
Propellerdamageiscausedbystriking
solidobjects.Ifthepropellerisnotrotating
at the time it strikes a solid object, the dam-
age is usually conned to just one blade
andmaybedifculttosee.Ifthepropeller
isrotatingwhenitstrikesanobject,usually
theresultingdamagecaneasilybeseenon
all blades.
Checking/Repairing Propellers
Step 1: Ensure the engine is OFF and the
emergency safety stop switch is
disconnected.
Step 2: Clamp a small rule scale to the
shaft strut, parallel to the shaft
so that the end of the scale is
3/32-inches from the leading edge
of a propeller blade.
Step 3: Rotatethepropellerslowly.There
should be no more than 3/32-inch
variance between the blades. If
the propeller is damaged, see an
authorized MasterCraft dealer.
Changing Propellers
Step 1: Ensure the engine is OFF and the
engine safety starting switch is
disconnected.
Step 2: Remove and discard the cotter
pin.
Step 3: Removethepropellernut.
Step 4: Tap the center hub of the propel-
ler with a rubber mallet to release
thepropeller.Inspecttheshaftand
propeller splines for damage.
Step 5: Thoroughlycleanandapplyalight
coat of waterproof marine multi-
purpose grease to the splined area
of the shaft and propeller.
Step 6: Alignthesplinesandcarefullyin-
stall the propeller onto the shaft.
DO NOT FORCE THE PRO-
PELLER INTO PLACE.
Step 7: Installthepropellernutandtorque
to50-ft-lbs.
Step 8:Installanewcotterpinandbend
the ends around the shaft to lock
the propeller on the shaft.
… 225 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mastercraft X30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mastercraft X30 in the language / languages: English as an attachment in your email.

The manual is 5,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info