671530
5
Zoom out
Zoom in
Previous page
1/13
Next page
FRONT PANEL FUNCTIONS (CONT.) FRONT PANEL FUNCTIONS (CONT.)
8. MASTER
Controls the overall volume level of your
CODE amplier.
MASTER Volume control settings are not
stored as part of a Preset.
9. PRESET
A Preset is a combination of preamp, power
amp & speaker models, with tonal settings
and FX: Chorus, Flanger, Tremolo, Delay
etc, stored to a single location within your
CODE amplier’s memory. This is like a
‘snapshot’ of the whole amplier’s settings
(excluding MASTER), which can be recalled
using the PRESET selector, or with the
optional CODE footcontroller.
Turn the PRESET selector to explore your
CODE amplier’s factory Presets.
To discover how to edit a Preset, go to
‘EDITING A PRESET’ in this manual
10. EDIT
Use the EDIT selector to deep edit a Preset.
Push the EDIT selector to preview the
stored Gain, Bass, Middle, Treble & Volume
settings. Turn the EDIT selector to view the
current Section Switch settings.
To discover how to edit a Preset, go to
‘EDITING A PRESET’ in this manual.
11. F/C
Use this jack socket to connect the
CODE footcontroller (PEDL-91009 sold
separately).
12. MP3 PLAYER INPUT
Use this dedicated mini-jack socket to
connect an MP3 player to practice with or
jam along to music.
13. HEADPHONE OUTPUT
Use this mini-jack socket to connect
headphones for ‘silent’ practice. This can
also be used as a line out.
14. ON/OFF
This is the mains power ON/OFF switch.
SECTION SWITCHES (15 - 21)
The Section Switches represent different ‘sections’ in the guitar signal chain. This is the
route that a guitar signal travels through a conventional amplier setup from the guitar to
the loud speaker(s).
15. PRE FX
This is where you will nd FX that would typically plug into a conventional amplier
between the guitar and the amplier’s input. These FX would typically be in pedal form,
and also known as ‘stompboxes’. The ‘stompbox’ FX in the PRE FX section are:
Compressor
Compressor affects an audio signal’s dynamic range. CODE’s compressor decreases,
or compresses’, any part of your guitar sound that peaks above a certain threshold.
Any part of your guitar sound that remains below the threshold is unaffected.
Compressor can add clarity and consistency to your guitar sound whether clean or
overdriven. Compressor’s editable parameters are:
‘STOMPBOX’ FX
A:>>|<<
A:>>|<<
POWER AMP
CABINET
PREAMP
ENGLISH ENGLISH
PARAMETER VALUE RANGE DESCRIPTION
Tone 0 - 10 Adjusts the Compressor’s higher and lower
frequencies.
Ratio 0 - 10 Controls how much Compression is applied to a signal
above the threshold.
Compression 0 - 10 Adjusts the point at which Compression is applied to
the signal.
Level 0 - 10 Controls the overall volume level of the Compressor.
Distortion
CODE’s stompbox Distortion’s three Modes simulate solid-state Distortion and
Overdrive FX pedals. GUV Mode is a Marshall Guv’nor™ with Drive and Tone
controls. ODR & DIS Modes provide avours of classic overdrive and distortion
stompboxes. Stompbox Distortion is particularly effective when used with classic
and vintage MST preamp models to provide more drive and sustain. Distortion’s
editable parameters are:
PARAMETER VALUE RANGE DESCRIPTION
Mode GUV, ODR & DIS Marshall Guv’nor, Classic OD pedal
& Classic Distortion pedal.
Drive 0 - 10 Controls the amount of Overdrive or Distortion
applied to the signal.
Tone 0 - 10 Adjusts the amount of upper mid and higher frequency
content in the Overdrive or Distortion before the
signal reaches the amplier panel tone controls.
Level 0 - 10 Controls Distortion’s overall volume level.
!
!
!
Marshall
STOMPBOX
MOD
DELAY
REVERB
15
16
16
17
18
19
20
21
1718
19
20
21
15
Marshall
STOMPBOX
MOD
DELAY
REVERB
15
16
16
17
18
19
20
21
1718
19
20
21
15
Pressing the Section Switches (#15 – #21 in this manual)
will activate (Red LED on) and bypass (LED off) that Section.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marshall Code 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marshall Code 50 in the language / languages: English as an attachment in your email.

The manual is 2,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marshall Code 50

Marshall Code 50 User Manual - English, German, French, Spanish - 69 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info