494328
8
Zoom out
Zoom in
Previous page
1/11
Next page
43
Single letter code receiving mode
If the letter code of the RFIX35 is programmed to any letter
code ("
A" to "O") the interface will only receive and forward the
programmed letter code. The remote control should be
programmed to the same letter code as the RFIX35.
All letter code receiving mode
If the letter code of the RFIX35 is programmed to letter code "P"
the interface will forward the programmed letter code in the
remote control. Independently which letter code is programmed
into the remote control( "
A" to "P"). The RFIX35 will receive all
letter codes and forward the received commands whenever
programmed into the remote control.
44
Programming of the RFIX35
Programming mode
In the programming mode the RFIX35 can be programmed to
receive only one user defined letter code (= select one lettercode
from A to O) or to receive all letter codes (A to P). When only one
letter code is programmed, the RFIX35 will only receive instructions
from remote controls within the receiving reach of the RFIX35
programmed on the same letter code. If for example the RFIX35 is
programmed on letter code B, the remote control also has to be
programmed on letter code B.
Security learn mode
In the security learn up to 8 RF-secured remote controls can be
linked to the RFIX35. Once the RFIX35 is programmed to function in
RF-secured mode, the RFIX35 will only accept RF-instructions from
linked remote controls. RF-instructions from other remote controls
within the receiving reach of the RFIX35 will be ignored. In this
mode you can also clear the memory of the RFIX35. All remote
controls linked to the RFIX35 will then be deleted. In this mode you
can also program the standard* receiving mode (non-secured)
whenever you have programmed the RF-secured mode previously.
Operation mode
In operation mode the RFIX35 will receive RF instructions from
remote controls and transpose them into Marmitek X-10 commands
on the power line.
*) Default is standard mode programmed to letter code A.
45
Programming
the letter code
Send a setup
command (letter
and number code)
(2x)
Press button
3 - 6 s
Press button
6 - 12 s
Press button
> 9 s
LED continuous ON
Shortly press
program switch
or wait 60 s
Letter code
programmed
LED flashes
Security
learn mode
Send security code
with remote control
(RF-secured)
Optional: clear memory
LED short blinks
Operation mode
LED OFF
Result:
secured mode
LED OFF
Memory
full
Code accepted Code NOT accepted
LED 2 s ON
Memory cleared
Result:
standard mode
1 2
3
46
Programming the RFIX35 (cont'd.)
Programming the letter code for the RFIX35
Activate the programming mode by keeping the programming
switch pressed for 3 to 6 seconds. The LED will now lit.
Send the setup command twice (letter code and number code),
through the power line by using e.g. Programming Unit
(PRU256), Marmitek X-10 Home Control Box or other X-10
compatible transmitters. The LED will blink twice after receipt of
two identical setup commands (Address). Letter code "
A" to "P"
may be programmed. For example, to program letter code B,
send B01 twice.
1
Press the programming switch in with a
pointed object.
47
Receive all letter codes
To receive all letter codes ("A" to "P") please program the RFIX35
on letter code "
P".
The LED will blink twice after receiving two identical setup
commands (Address) in the program mode.
CHOICE CHOOSE ACTION RESULT
Address Setup Command LED flashes
SINGLE A01…016 2 x Address 2 x
ALL P1…P16 2 x Address 2 x
Ending the programming mode
Shortly press the programming button mode or just wait
60 seconds to return to the operation mode.
Note: It is not possible to program the RFIX35 with
a remote control only. To program the IRIX35 with
the remote control an additional remote control
receiver is required to send the setup commands
over the power line to the RFIX35.
!
48
Programming the RFIX35 (cont'd.)
Press the programming switch in with a pointed object.
Programming the RFIX35 to the RF-secured mode
Activate the RF-secured programming mode by keeping the
programming switch pressed for 6 seconds. The LED will now
give quick short blinks.
2
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek RFIX35 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek RFIX35 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info