494328
6
Zoom out
Zoom in
Previous page
1/11
Next page
31
Marmitek is niet verantwoordelijk voor het disfunctioneren
van het Marmitek X-10 systeem als gevolg van in het
gebouw aanwezige apparatuur met emissiewaardes boven
de maximale toegestane niveaus zoals die gelden in
residentiële, commerciële en lichtindustriële omgevingen en
zijn vastgelegd in de EN 61000-6-3.
Toepassing Geldende Europese norm
Marmitek X-10 huis
automatisering*
Immuniteit van Emissie van Immuniteit- en
de apparatuur de apparatuur emissienorm
Residentieel 61000-6-1 61000-6-3 Compatibel/
Commercieel voldoet
Licht-industrieel
* Voorwaarde daarbij is dat het gehele Marmitek X-10 systeem wordt
geïnstalleerd volgens de geldende instructies door een gecertificeerde
en getrainde Marmitek X-10 dealer.
Copyrights
Marmitek is a trademark of Pattitude B.V., RFIX35™ is a trademark of Marmitek
B.V. All rights reserved. Copyright and all other proprietary rights in the content
(including but not limited to model numbers, software, audio, video, text and
photographs) rests with Marmitek B.V. Any use of the Content, but without limi-
tation, distribution, reproduction, modification, display or transmission without
the prior written consent of Marmitek is strictly prohibited. All copyright and
other proprietary notices shall be retained on all reproductions.
20325 - 20100928
Marmitek X-10
Radio Frequency interface type RFIX35
34
Technical characteristics
Transposes Radio Frequency (RF) signals from remote control
devices into Marmitek X-10 commands on the power line.
(See page 56 for RF-signal information).
Possibility to receive standard RF or "RF-secured" codes.
In "RF- secured" mode possibility to link up to 8 secured
remote controls or transmitters.
Controls up to a maximum of 256 addresses (Lettercode
A to P).
Possibility to control only one user definable letter code
(16 addresses).
Designed as a wall- or ceiling mountable unit or stand-alone
use.
The radio frequency protocol is compatible with the X-10
RF protocol. This means that all standard X-10 compatible
RF remote transmitters (controls) can be used.
Application options
The RFIX35 can be used to receive RF-commands from
Marmitek X-10 remote controls and send them over the power
line to switch or dim actuators (see figure 1).
Marmitek X-10 Radio Frequency interface type RFIX35
35
Figure 1.
Marmitek X-10 modules
RFIX35
Lighting
circuit
signal
RF
signals
Remote control
(ABX1 of ABX3)
Movement sensor
Marmitek
Home Control
Box
Marmitek X-10 Home Control Box
If the RFIX35 is used in combination with the Marmitek X-10
Home Control Box the RFIX35 can be used to activate the
previously programmed macros in the Marmitek X-10 Home
Control Box, using a remote control device.
36
In principle, the RFIX35 can be used in two ways:
1. Fitted to a distribution box.
2. Connected to a wall socket.
Note: Switch off the power before starting the
assembly!
Fitting to a distribution box
To fit the RFIX35 to a distribution box, follow the steps below.
Remove the cover of the RFIX35 by loosening the screw at
the top.
Feed live and neutral through the rear plate by making an
opening through the sticker covering the mounting plate.
Firmly screw the mounting plate with screws to the
distribution box.
Connect live and neutral to the connector of the
mounting plate.
Firmly tighten the cover of the RFIX35 to the mounting
plate again.
!
Assembly
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek RFIX35 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek RFIX35 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info