494268

Marmitek MS13 Manual

6
Zoom out
Zoom in
Previous page
1/40
Next page
• Now press the <house/on> button the number of times that corresponds to the house-code that you
want to set. On the last press hold down the button (e.g. for house-code C press the <house/on>
button 3 times and hold the button down on the third press).
• After 3 seconds the LED will display the new setting. If you wait too long, or if an error occurs, the red
LED will flash rapidly. In this case no changes are implemented and you should start again from the
beginning.
PROGRAMMING THE UNIT-CODE
• Press the <unit/off> button and hold it down.
• The red LED will start to flash.
• 3 seconds later the LED will display the current unit-code setting (the factory setting is 1).
• 1 flash for 1.
• 2 flashes for 2.
• …
• 16 flashes for 16.
• Release the <unit/off> button.
• Now press the <unit/off> button the number of times that corresponds to the unit-code that you want to
set. On the last press hold down the button (e.g. for unit-code 3 press the <unit/off> button 3 times and
hold the button down on the third press).
• After 3 seconds the LED will display the new setting. If you wait too long, or if an error occurs, the red LED
will flash rapidly. In this case no changes are implemented and you should start again from the beginning.
SETTING THE SENSOR FOR DAY/NIGHT USE
• Press the <unit/off> button once.
• The LED will flash briefly.
• Press the <house/on> button and hold it down.
• The green LED behind the PIR lens will light up.
• 3 seconds later the LED will display the current mode (the factory setting is 1).
• 1 flash when the motion detector is on during the day, light/dark sensor off.
• 2 flashes when the motion detector is off during the day, light/dark sensor off.
• 3 flashes when the motion detector is on during the day, light/dark sensor on.
• 4 flashes when the motion detector is off during the day, light/dark sensor on.
• Release the <house/on> button.
• Now press the <house/on> button the number of times that corresponds to the mode that you want
to set. On the last press hold down the button (e.g. for mode 3 press the <house/on> button 3 times
and hold the button down on the third press).
• After 3 seconds the LED will display the new setting and the LED will switch off.
SETTING THE DELAY TIME
(the length of time that the lamp will remain illuminated after the last motion has been detected)
• Press the <house/on> button once.
• The LED will flash briefly.
• Press the <unit/off> button and hold it down.
• The green LED behind the PIR lens will light up.
• 3 seconds later the LED will display the current mode (the factory setting is 1):
• 1 flash for 1 minute.
• 2 flashes for 2 minutes.
• 3 flashes for 4 minutes.
6 © MARMITEK
manual MS13 05-12-2006 09:54 Pagina 6
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek MS13 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek MS13 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info