494268

Marmitek MS13 Manual

5
Zoom out
Zoom in
Previous page
1/40
Next page
The MS13 is fully wireless, the signal is transmitted straight through walls and ceilings and it is
suitable for outdoor use.
OPERATION
The MS13 motion detector sends radio signals to an X10 transceiver (Marmitek X10 TM13 or Marmitek X10
Alarm station). The transceiver or station then transmits these signals wirelessly via the electric cabling that is
already in your house to switch lights (or appliances) that are connected to X10 receivers on and off. The
Marmitek X10 TM13 and a Marmitek X10 CM11 computer interface can also be used to activate previously
programmed macros. The MS13 can also be programmed to detect motion both at night and during the day,
or only at night. The Marmitek X10 MS13 can also be used to detect the transition from light to dark and
vice versa.
INSTALLATION
Slide the antenna sleeve over the sensor’s wire antenna. Press the sleeve into the clamp on the top of the
sensor. Insert 2 AAA batteries into the MS13’s battery compartment. The cap on the front of the sensor
must be removed using tweezers or small pliers in order to open the battery compartment. Now the screw
that is locking the lid can be unscrewed. Replace the cap if the sensor is to be used outdoors.
• After inserting the batteries it will take 30 seconds for the MS13 to become active.
• After a signal has been transmitted the MS13 will be inactive for 10 seconds.
• The default setting for the house-code that is transmitted is A (factory setting).
• The default setting for the unit-code that is transmitted for motion detection is 1 (factory setting).
• The unit-code that is transmitted for light / dark detection is always the unit-code that has been set + 1
(example: If you have the motion detection code set to A3 the code for light/dark is automatically A4).
The default setting for this function is off (factory setting).
• When motion is detected an <on> command is transmitted.
• When the <house/on> button is pressed once an <on> command is transmitted.
• When the <unit/off> button is pressed once an <off> command is transmitted.
• On transition from light to dark an <on> command is transmitted for the unit-code that has been
set +1.
• On transition from dark to light an <off> command is transmitted for the unit-code that has been
set +1.
• When motion is detected an <on> command is transmitted for the unit code that has been set.
• After the last motion detection plus the set delay (factory setting 1 minute) an <off> command is
transmitted for the unit code that has been set.
PROGRAMMING THE HOUSE-CODE
Unlike most Marmitek X-10 Modules the MS13 does not have code wheels.
• Press the <house/on> button and hold it down.
• The red LED will start to flash.
• 3 seconds later the LED will display the current house-code setting (the factory setting is A).
• 1 flash for A.
• 2 flashes for B.
• …
• 16 flashes for P.
• Release the <house/on> button.
5MS13
TM
ENGLISH
manual MS13 05-12-2006 09:54 Pagina 5
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek MS13 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek MS13 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info